User manual GAGGENAU AW211190

[. . . ] Operating and Assembly Instructions AW 200 AW 201 AW 202 AW 210 AW 211 Extractor Hood AW 200 AW 201 AW 202 AW 210 AW 211 Preface 1. Important notes 1. 1 For your safety 1. 2 Operating for the first time 1. 3 About use 2. Assembly instructions 6. 1 Technical data 6. 2 Installation Page 3-4 Page 3 Page 4 Page 4 Page 5 Page 6-8 Page 9-10 Page 11 Page 12-17 Page 12 Page 12-17 1 Preface With your new extractor hood, working in the kitchen will be even more fun. The appliance offers you a number of advantages: ­ a good extraction capacity with low noise values, ­ a large number of control functions, ­ optimum illumination of the cooking surface by a dimmable halogen light. [. . . ] 6 If you press the Int key while the hood is running at fan level 1, 2 or 3, the electronic control will switch back automatically to the previously selected fan level after 5 minutes (see Fig. 7 If you would like to end the intensive level before the five minutes have elapsed, press the 0 key ("Motor off") or select a different level (see Fig. It is possible to switch off the extraction function at any time by pressing the 0 key (motor "off"). Fig. 8 7 Special functions: Intensive time: You can set the intensive level running time to 3, 5 or 10 minutes by simultaneously pressing the Int key and the 1, 2 or 3 key and you can store this setting (see Fig. First press the required key 1, 2, 3 or Int and then press the key (see Fig. After these ten minutes, the ventilation switches off, but the lighting stays on. or or or Fig. 11 or or Interval ventilation: Interval ventilation is a special feature of this appliance which periodically activates the fan for five minutes every hour. You can activate this function by simultaneously pressing the 0 key and, depending on the required extraction capacity, the 1, 2 or 3 key (see Fig. This mode of operation is indicated by alternating illumination of the key together with the corresponding fan level indicator. You can switch off interval ventilation by pressing the 0 key (see Fig. Cleaning and care Cleaning the grease filters The grease filter saturation display F flashes after an operating time of 30 hours to you indicate to you that you should clean the grease filter (see Fig. The grease filters can of course be cleaned at any time, even if the grease filter saturation display has not started to flash. The stainless steel grease filters can be removed easily for cleaning (see Fig. Then pull the grease filter downwards out of the holder; repeat the operation for the other grease filters. You can clean the stainless steel grease filters in a dishwasher at a maximum temperature of 65°C, where it should be supported vertically to allow food or rinsing residues to drain off. If possible, the inner parts of the housing should be wiped out in hot rinsing water when replacing the filters. Caution: when cleaning the inside of the housing, beware of protruding parts. Fig. 13 After having cleaned them, re-insert the grease filters in the wall extractor in reverse order. Important: the handles of both grease filters must be visible after assembly. Fig. Flashing of the indicating lamp goes off. 9 Cleaning the extractor hood Clean the exterior of your extractor hood with a soft cloth and mild detergent solution. Clean the stainless-steel extractor hood (AW 200/AW 202/AW 210) with stainless steel cleaner. ceramic cups) on the hood. Circulating air mode The activated charcoal filter eliminates kitchen smells in the circulating air mode. [. . . ] Switch the extractor hood to the highest setting when three or more burners of a gas cooker are used simultaneously. The following note applies to extractor hood AW 202 only; this model does not have an integrated fan: The extractor hood can only be used in exhaust air mode. The exhaust air is conveyed upwards through an externally attached fan via a ventilation shaft or directly into the open air through the outer wall. We recommend the fan modules GB 032-107 or GB 052/053-140 from our Gaggenau range; the extractor's electronic circuitry is optimised for these fan modules. For the electrical connection between the extractor hood and external fan see installation instructions for the external fan. [. . . ]