User manual GAGGENAU AW541721

[. . . ] Operating and Assembly Instructions AW 540-720 AW 541-720 Extractor Hood AW 540-720 AW 541-720 Preface Safety notes 1. Important notes 1. 1 For your safety 1. 2 Operating for the first time 1. 3 About use 2. Assembly instructions 6. 1 Technical data 6. 2 Installation Page 3 Page 4-5 Page 4 Page 5 Page 5 Page 6 Page 7-9 Page 10-11 Page 12 Page 13-18 Page 13 Page 14-18 1 Preface With your new extractor hood, working in the kitchen will be even more fun. The appliance offers you a number of advantages: ­ a good extraction capacity with low noise values, ­ a large number of control functions, ­ optimum illumination of the cooking surface by a dimmable halogen light. [. . . ] 6 If you press the Int key while the hood is running at fan level 1, 2 or 3, the electronic control will switch back automatically to the previously selected fan level after 5 minutes (see Fig. 7 If you would like to end the intensive level before the five minutes have elapsed, press the 0 key ("Motor off") or select a different level (see Fig. It is possible to switch off the extraction function at any time by pressing the 0 key (motor "off"). Fig. 8 8 Special functions: Intensive time: You can set the intensive level running time to 3, 5 or 10 minutes by simultaneously pressing the Int key and the 1, 2 or 3 key and you can store this setting (see Fig. First press the required key 1, 2, 3 or Int and then press the key (see Fig. After these ten minutes, the ventilation switches off, but the lighting stays on. or or or Fig. 11 or or Interval ventilation: Interval ventilation is a special feature of this appliance which periodically activates the fan for five minutes every hour. You can activate this function by simultaneously pressing the 0 key and, depending on the required extraction capacity, the 1, 2 or 3 key (see Fig. This mode of operation is indicated by alternating illumination of the key together with the corresponding fan level indicator. You can switch off interval ventilation by pressing the 0 key (see Fig. Cleaning and care Cleaning the grease filters The grease filter saturation display F flashes after an operating time of 30 hours to you indicate to you that you should clean the grease filter (see Fig. The grease filters can of course be cleaned at any time, even if the grease filter saturation display has not started to flash. The stainless steel grease filters can be removed easily for cleaning (see Fig. Then pull the grease filter downwards out of the holder; repeat the operation for the other grease filters. You can clean the stainless steel grease filters in a dishwasher at a maximum temperature of 130 °F / 55 °C, where it should be supported vertically to allow food or rinsing residues to drain off. If possible, the inner parts of the housing should be wiped out in hot rinsing water when replacing the filters. Caution: when cleaning the inside of the housing, beware of protruding parts. Fig. Push in the clips on the side of the activated charcoal filter and remove the activated charcoal filter downwardly. Push the clips to the side and remove the activated charcoal filter towards the front. Insert the activated charcoal filter at an angle (Note: be careful not to damage the light connector on the left side). Then push the filter upwards, until the clips on the side lock into place. Activated charcoal filters (KF 001-010) are available through your specialist dealer. [. . . ] Switch the extractor hood to the highest setting when three or more burners of a gas cooker are used simultaneously. 15 15 (19/32") Important: before marking the securing holes, make sure that no electricity or water lines or other lines are laid at the drilling points in the wall. 300 (11 13/16") Proceed as follows: ­ From the bottom edge of the hood, mark a center line on the wall. ­ With the aid of the drilling template, mark the positions of the screws on the wall (Fig. Note: this hood has been approved for installations as low as 30 ´ ´ and as high as 36 ´ ´ above the cooktop. [. . . ]