User manual GAGGENAU DI 461-131

[. . . ] Gaggenau Operating instructions Dishwasher DI 460-131 DI 461-131 W3128_A (AU) (Ref. 9000 407 108 (8811) en) en Index 4 4 4 4 4 4 4 4 5 5 5 5 6 6 6 6 6 7 7 7 8 8 8 8 8 8 8 8 9 9 9 9 10 10 10 11 12 12 12 13 13 13 13 13 13 13 Washing the dishes . 13 13 13 13 14 14 14 14 14 15 15 15 15 15 15 16 16 16 16 17 17 17 17 17 18 18 19 19 19 20 20 20 20 20 20 21 21 21 21 21 Safety instructions . . Safety instructions Delivery Check the packaging and dishwasher immediately for damage caused in transit. [. . . ] The spray pressure in the lower basket is intensified, the rinsing temperature is increased slightly. Warning Please ensure that the intake opening 25 is not obstructed and do not place any temperature-sensitive utensils in the lower basket at the rear right side above the blow opening 26 . The blow opening becomes hot and, furthermore, any damage will result in a callout by customer service. Extra drying * An increased temperature during the final rinse and an extended drying phase mean that even plastic parts dry well. There is a slight increase in the energy consumption. 13 Switching on the appliance Turn on the tap fully. This programme remains selected if no other programme button 2 is pressed. The programme starts running. Timer programming You can delay the start of the programme in 1-hour steps up to 24 hours. Press 8 + or ­ button until the displayed time corresponds with your requirements. To delete timer programming, press the 8 + or ­ is indicated on the digital display 7 . button until You can change your programme selection at any time until the programme starts. Close the door. Remaining running time display When the programme is selected, the remaining running time of the programme is indicated on the digital display 3 . The running time is determined during the programme by the water temperature, the number of utensils as well as the degree of soiling and may vary (depending on the selected programme). End of programme The programme has ended when the value is indicated on the numerical display 3 . Hold down programme button A and press START button 10 until on the digital display is indicated. The LED for button A flashes and the digital display displays the factory setting . Press programme button A until the factory set value is indicated on the digital display . Each time the button is pressed, the set value increases by one level; when the value of has been reached, the display jumps back to (off). Close the door. Display window Apart from information on the programme sequence, the display window 12 also indicates additional information on e. g. If you would no longer like to have this additional information displayed, proceed as follows. Hold down programme button A and press START button 10 until on the digital display is indicated. The LED for button A flashes and the digital display displays the factory setting . Press programme button A until the factory set value is indicated on the digital display 3 . To change the setting, By pressing the C button, you can switch the onboard computer (additional programme or on . Close the door. 14 Switching off the appliance Short time after the end of the programme: Open the door. Remove the utensils when they have cooled down. Intensive drying The final rinse uses a higher temperature which improves the drying result. [. . . ] Only this extension which features the guarantees compliance with the currently valid regulations. Please note the system will function only when the power supply is connected. Waste-water connection The required work sequence can be found in the installation instructions. Connect the waste-water hose to the drainage connection of the siphon with the enclosed parts. Ensure that the drainage hose is not kinked, crushed or twisted and that there is no cover plate in the drainage to prevent the waste water from flowing out! Removing the appliance Also observe the sequence of worksteps here. [. . . ]