User manual GAGGENAU KG260224CA

[. . . ] Operating and assembly instructions KG 260 CA Gas cooker KG 260 CA FOR YOUR SAFETY Page 2 Warnings Page 3 Preface Page 4 1. Important notes Page 5-6 1. 1 For your safety Page 5 1. 2 Operating for the first time Page 5 1. 3 About use Page 6 2. Structure and operating principle Page 7-8 2. 1 Structure Page 7 2. 2 Special accessories Page 7 2. 3 Operating principle Page 8 3. Maintenance Page 11 5. 1 General Page 11 5. 2 Remedying slight malfunctions yourself Page 11 6. [. . . ] A minimum distance of 15 mm (19/32") must be observed between the control knob and the pot or pan. In the event of malfunctions, contact your specialist dealer or your responsible Gaggenau after-sales service. Tip: When buying pots, pay attention to the fact that the manufacturer frequently specifies the top pot diameter, which is generally larger than the diameter of the base. Use cooking utensils that the manufacturer states as being "suitable for gas". Preferably use the larger cooking zone for brief cooking, deep fat frying and brief frying of large quantities. Preferably use the smaller ring for soaking, warming up and keeping warm, even when large quantities are involved. 2. Structure and operating principle 2. 1 Structure 1 Pot grille 1 2 High burner, 9500 BTU (2. 8 kW) 2 3 2 3 3 Normal burner, 6500 BTU (1. 9 kW) 4 Control knob for the front left cooking position 5 Control knob for the rear left cooking position 6 Control knob for the rear right cooking position 7 Control knob for the front right cooking position Fig. 2 4 5 6 7 8 Burner head cover 8 9 Burner head 10 Spark plug for automatic ignition 11 Thermal sensor to safeguard the flame 9 10 Fig. 3 11 2. 2 Special accessories You can order the following special accessories: ­ VV 200-000: Connecting strip ­ VD 201-010: Appliance cover (If an appliance cover is fitted, the pot support must be removed when closing. ) 7 2. 3 Operating principle The appliance features one-hand operation. That is to say, the ignition is activated when the control knob is pressed briefly. After igniting, keep the control knob pressed for around 5-8 seconds more because the heat sensor that opens the gas channel has to warm up first. ­ As the result of heat development, slight discoloration can appear on the stainless steel surface. Distribute stainless steel care agents uniformly and thinly on the hob (not on the control panel!). This will ensure an even surface and will keep your hob in a good condition for a long period of time. When assembling, place the burner cover (1) on the burner head (2) so that the four tabs on the bottom edge of the burner cover engage in the corresponding tabs on the burner head (see Fig. 7 Wipe off spilt food immediately, thus ensuring that it cannot burn in on the hob. You should only clean the control panel and the control knobs with detergent and a a soft cloth. To ensure perfect functioning, keep the thermal sensor and the spark plug clean. Keep the incoming air openings on the rear of the panel unobstructed and clean. Caution: Never use high-pressure or steam jet units to clean your appliance because otherwise the electrical safety of the appliance will no longer be guaranteed. 10 5. Maintenance 5. 1 General The appliance must be disconnected from the power supply during all repair work. In the event of malfunctions, check whether the gas and electricity supply is in proper working order, i. e. If the power supply is functioning correctly, but your appliance still does not work, please contact your Gaggenau dealer who will provide you with the address and telephone number of your nearest manufacturer's authorized service agent or contact Gaggenau USA on (800) 828-9165. [. . . ] ­ Remove the cover from the underside of the appliance under the gas valves. The low-setting nozzle 1 is located in the gas valve and is screwed in from below. 10) ­ Unscrew the nozzle and insert the new nozzle as specified in the low-setting nozzle table. If it should be necessary to correct the low-setting nozzle 1 as the result of deviating gas types and pressure, the flow rate can be increased by turning to the left. Fig. [. . . ]