User manual GAGGENAU RX496290

[. . . ] Gaggenau en Installation instructions RX 496 Table of Contents Safety and warning notes . Clearance from the appliance to the handle of the adjacent kitchen unit . Connecting the appliance to the water main Connecting the appliance to the mains . Fitting the appliance into the kitchen counter Fitting the kitchen unit doors . [. . . ] The height of the ventilation opening must be no less than 80 mm, otherwise the refrigeration unit may malfunction and become damaged. Height of the ventilation opening less than 130 mm: There must be space behind the appliance to allow warm air to dissipate. The appliance would otherwise be forced to work harder, which would increase power consumption. With the appliance feet fully screwed in and a ventilation opening at a height of 80 mm, the minimum base clearance is 100 mm. 10 Door opening angle The appliance is delivered from the factory with its doors adjusted to the maximum opening angle. The maximum door opening angle is 108° and overlaps the kitchen front. The maximum door opening angle can be retained with kitchen unit doors up to 21 mm thick. If the kitchen unit doors are thicker (up to 24 mm), it is necessary to reduce the door opening angle. Clearance from the appliance to the wall 3 min. 10 Clearance from the appliance to the handle of the adjacent kitchen unit 3 W D2 E min. 10 B W W D1 C B 108° up to 21 up to 50 300 108° up to 21 96° up to 24 96° up to 24 up to 100 300 B [mm] E [mm] D2 [mm] up to 100 up to 50 350 250 B W: Door opening angle B: Thickness of the kitchen unit doors C: Depth of the appliance handle D2: Clearance to the wall 96° up to 24 up to 100 30 W B [mm] C [mm] D1 [mm] 108° up to 21 up to 50 40 108° up to 21 96° up to 24 up to 100 up to 50 60 25 W: Door opening angle B: Thickness of the kitchen unit doors C: Depth of the handle of the adjacent kitchen unit D1: Distance between the handle and the adjacent kitchen unit 11 Required tools and accessories Scope of delivery D D D D D D D D D D Knife with adjustable blade Measuring tape Try square Spirit levels 60 cm and 120 cm long Featheredge min. 120 cm long Refrigerator and freezer unit Assembly instructions Instructions for use Drilling template for kitchen unit doors Installation accessories Miscellaneous D D D D Accessories Supply or outlet hose extension requires one each of Accessories no. ET 212397 Syphon connection Stepladder Dolly or lift truck Wood screws of various sizes Thin (max. linoleum) Suitable material for covering and protecting the cabinets (e. g. protective film) Adhesive tape D Reducer 3/4 inch to 1 inch Accessories no. ET 155903 Modification kit for wall fixing and mounting of side parts Accessories no. Wb 010 090 For free standing appliances, the angle brackets for the wall fixing are included. ZB 022 090 D Tools D D D D D D D D T20 cordless screwdriver T20 Torx screw driver T20 Torx bit + magnetic retainer 8 mm socket wrench Hammer drill for drilling holes in the wall and floor Drill bits of various sizes for various materials Open end spanner, WAF 19 mm Monkey wrench 12 Fitting the appliance 1. To prevent the appliance from tipping over, do not open the appliance doors until the anti tip stabiliser has been fitted. Proceed with great care, otherwise persons could be injured or the appliance could be damaged. To protect the floor surface from damage during installation: D To ensure safe and troublefree installation and an optimum overall appearance of the kitchen front, the following points must be checked beforehand: !D D D D Floor surface of the installation niche Dimensions of the installation niche Squareness of the installation niche Clearance from the installation niche to adjacent kitchen units and wall Location of the socket Location of the fresh water and outlet connections Stability and security of adjacent cabinet parts All cabinet parts onto which the appliance is screwed must be firmly connected to the wall. D D D Lay a strip of linoleum or similar on the floor to the front of the planned area of installation and fix down with adhesive tape. Transport accessories must be positioned against the centre of the back or sides of the appliance. Never slide the transport accessory underneath the appliance from the front. [. . . ] Using the levelling screws, adjust the furniture door vertically and laterally for correct alignment. Fit the angle bracket between the furniture door and appliance door from underneath. The appliance uses the door covers to detect whether the appliance doors are closed. 16. Secure the angle bracket to the existing holes in the appliance door using one screw for each hole. [. . . ]