User manual GAGGENAU VG421210CA annexe 2

[. . . ] Operation, Maintenance and Installation Manual VG 421 AU Built-in gas hob VG 421 AU FOR YOUR SAFETY Warnings 1. Important Notes For Your Safety Operating for the First Time About Use 2. Installation Instructions Important Notes on Installation Connecting the Appliance Preparing the Cabinet Installing the Hob Installing the Spindles Nozzle Replacement Fitting the Appliance Cover Page 2 Page 3 Page 5-6 Page 5 Page 5 Page 6 Page 7 Page 7 Page 7 Page 7 Page 8 Page 9 Page 10 Page 11 Page 12-13 Page 14 Page 15 Page 16-17 Page 18-26 Page 18 Page 19 Page 20 Page 21 Page 22-23 Page 24-25 Page 26 1 FOR YOUR SAFETY WARNING: If the information in this manual is not followed exactly, a fire or explosion may result causing property damage, personal injury or death. Do not spray aerosols in the vicinity of this appliance while it is in operation. WHAT TO DO IF YOU SMELL GAS: ­ Do not try to light any appliance. [. . . ] · First lift the pot grid with both hands (be careful not to scratch the base). · Remove the burner head cover, the burner rings and the burner head. · As the result of heat development, slight discoloration can appear on the stainless steel surface. Distribute stainless steel care agents uniformly and thinly on the hob. This will ensure an even surface and will keep your hob in a good condition for a long period of time. Damp burner parts will cause malfunctions when igniting or unstable flames. · When assembling the burner parts, make sure that the burner ring and burner head are placed in such a way that the locking lugs fit in the corresponding recesses. burner head electrode burner base Note: to avoid jeopardising the electrical safety of the appliance, do not use high-pressure or steam jet cleaning devices ­ risk of short circuits!Before cleaning, please wait until the cooktop has cooled to hand-warm. 12 Part / Material Pot Grid (enamel on cast iron) Burner Head Cover, Burner Ring, Burner Head (brass) Electrode Suggested Cleaning Procedure Take pot grids off for cleaning. Clean with brush, fine glass-paper or scouring pad. Important Reminders Do not clean in a dishwasher. Abrasive cleaners, used too vigorously or too often can eventually mar the enamel. Soiled electrodes may cause malfunctions when igniting or flame control disturbance. To prevent marring the polished stainless steel trough, always polish in the direction of the polish lines. Light discolorations may form if the natural oxidation is removed together with the soiling. Put some commercially available stainless steel polish on a cloth and polish the whole cooktop after cleaning to get an even stainless steel surface. Never allow food stains or salt to remain on stainless steel for any length of time. Chlorine or chlorine compounds in some cleaners are corrosive to stainless steel. Cloth should not be too wet, as moisture could penetrate behind the control knob. Base (stainless steel, shot blasted, brushed) Cloth with detergent and hot water. After cleaning, polish dry with a soft cloth to prevent water stains forming on the surface. For heavy soiling, you can order our stainless steel cleaner (Order No. Caution: no liquid should enter the housing of the cooktop through the burner base. Control knob Wipe with a damp cloth. 13 8. Maintenance The appliance must be disconnected from the power and gas supply during all repair work. [. . . ] 2 The gas taps of the burners must be in the off position (flat side to the top). Connect the appliance to the power supply, and check for correct functioning. If the appliance switches off there may be air in the gas supply line. This may need to be repeated until the appliance ignites. 38 spindle covers 22 23 Nozzle Replacement Changing over to a different gas type Only authorised specialists are permitted to change over to a different gas type. [. . . ]