User manual GAGGENAU VG441110F

[. . . ] Operation, Maintenance and Installation Manual VG 441-110/110F VG 441-210 Gas Wok VG 441-110/110F VG 441-210 1. Important Notes For Your Safety Operating for the First Time About Use 2. Installation Instructions Important Notes on Installation Connecting the Appliance Preparing the Cabinet Installing the Control Panel Installing the Cooker Nozzle Replacement Page 3-4 Page 3 Page 3 Page 4 Page 5 Page 5 Page 5 Page 5 Page 6 Page 7 Page 8 Page 9 Page 10 Page 11-12 Page 13 Page 14 Page 15-16 Page 17-23 Page 17 Page 18 Page 19 Page 20 Page 21 Page 22-23 1 Congratulations on buying your new "Vario" appliance. Before switching your appliance on for the first time, we would like you to familiarize yourself with your new appliance. [. . . ] Do not use scouring agents, abrasives or chemically aggressive cleaners (for example oven cleaner)!Before cleaning, please wait until the cooktop has cooled to hand-warm. · First lift the pot grid with both hands (be careful not to scratch the base). · Remove the burner head cover, the burner ring and the burner head. · As the result of heat development, slight discoloration can appear on the stainless steel surface. Distribute stainless steel care agents uniformly and thinly on the hob. This will ensure an even surface and will keep your hob in a good condition for a long period of time. Damp burner parts will cause malfunctions when igniting or unstable flames. · When assembling the burner parts, make sure that the burner ring and burner head are placed in such a way that the locking lugs fit in the corresponding recesses. 11 burner ring burner head heat sensor electrode burner base Note: to avoid jeopardising the electrical safety of the appliance, do not use high-pressure or steam jet cleaning devices ­ risk of short circuits!Before cleaning, please wait until the cooktop has cooled to hand-warm. Do not block the ventilation openings. Part / Material Pot Grid (enamel on cast iron) Burner Head Cover, Burner Ring (brass) Burner Head (enamel on cast iron) Base (stainless steel, shot blasted, brushed) Suggested Cleaning Procedure Take pot grids off for cleaning. Clean with detergent and brush. Important Reminders Do not clean in a dishwasher. Abrasive cleaners, used too vigorously or too often can eventually mar the enamel. Port openings must be kept free. Do not clean in a dishwasher. Cloth with detergent and hot water. After cleaning, polish dry with a soft cloth to prevent water stains forming on the surface. For heavy soiling, you can order our stainless steel cleaner (Order No. Caution: no liquid should enter the housing of the cooktop through the burner base. To prevent marring the polished stainless steel trough, always polish in the direction of the polish lines. Light discolorations may form if the natural oxidation is removed together with the soiling. Put some commercially available stainless steel polish on a cloth and polish the whole cooktop after cleaning to get an even stainless steel surface. Never allow food stains or salt to remain on stainless steel for any length of time. Chlorine or chlorine compounds in some cleaners are corrosive to stainless steel. [. . . ] · As shown in the installation sketch, drill the Ø 35 mm hole to secure the control knob in the cabinet front. 180 490 min. 5 0 35 45 360 60 · If the cabinet front is thicker than 26 mm, the front must be routed from the back to max. 26 mm on an area of 80 x 310 mm. 1170 765 1575 ­ 19 Installing the Control Panel Note: only install control panel with appliance of the corresponding type. Before connecting the appliance, make sure the electricity is switched off at fuse point! [. . . ]