Detailed instructions for use are in the User's Guide.
[. . . ] Full display or unclear display during operation indicates the batteries have been used up. If the remote controller can't run normally during operation, please remove the batteries and reload several minutes later.
Hint: Remove the batteries in case unit won't be in usage for a long period. If there are any display after taking-out, just need to press reset key.
TIMER
TIME -
LIGHT
LOCK
CODE
RESET
2
Operation
Base Operation
+ TEMP
Emergency operation and test operation
Emergency Operation:
FAN TEMP
Remote controller
HEALTH
MODE
HEALTH AIRFLOW
SWING
SLEEP
FRESH
SWING
Use this operation only when the remote controller is defective or lost. When the emergency operation switch is pressed, the" Pi "sound is heard once, which means the start of this operation. [. . . ] In SOFT operation mode, fan speed automatically takes low speed
of AUTO fan mode.
Note
During POWER operation, in rapid HEAT or COOL mode , the room will show inhomogeneous temperature distribution. Long period SOFT operation will cause effect of not too cool or not too warm. To cancel POWER or SOFT operation Press POWER/SOFT button again , POWER or SOFT disappears.
1 hr
1 hr
Rises 1OC
Temp. setting
Unit stop
In COOL, DRY mode
2. In HEAT mode
1 hours after SLEEP mode starts, temp will become 2 C lower than temp. setting. After another 1 hours, temp decrease by 2 OC futher. After more another 3 hours, temp. rises by 1OC futher. The unit will run for further 3 hours then stops. Temp. is lower than temp. setting so that room temperature won't be too high for your sleep.
Temp. setting
1 hr Decreases 2OC 1 hr Decreases 2OC 3 hrs 3 hrs
Rises 1OC
O
HEALTHY Operation
Unit stop
Healthy Negative ions
The anion generator in the airconditioner can generate a lot of anion effectively balance the quantity of position and anion in the air and also to kill bacteria and speed up the dust sediment in the room and finally clean the air in the room.
SLEEP operation starts
SLEEP operation stops
About UV light degerming function
UV light emitted by the UV light device of the indoor unit catalytically activates the nano TiO2 on the multi-lights touching intermediary, and the degerming effect is highly efficient and lasting. Note: when the function is running, don't open the inlet grille.
In HEAT mode
3. In AUTO mode
The unit operaters in corresponding sleep mode adapted to the automatically selected operation mode.
4
Operation
Timer On/Off On-Off Operation
Set clock correctly before starting TIMER operation. Every time the button is pressed, display changes as follows: Remote controller:
BLANK
TIMER ON TIMER OFF TIMER ON-OFF
EUROPEAN REGULATIONS CONFORMITY FOR THE MODELS
CE
All the products are in conformity with the following European provision: - Low Voltage Directive 73/23/EEC - Low Voltage Directive 2006/95/EC -Electomagnetic CompatibilitY 89/336/EEC -Electomagnetic CompatibilitY 2004/108/EC
ROHS
The products are fulfilled with the requirements in the directive 2002/95/EEC of the European parliament and of council on the Restriction of the use of Certain Hazardous Substances in Electrical and Electronic Equipment (EU RoHS Directive)
Then select your desired TIMER mode (TIMER ON or TIMER OFF or TIMER ON-OFF). 4. After setting correct time, press SET button to confirm " "or" " on the remote controller stops flashing. 5. Cancel TIMER mode Just press TIMER button several times until TIMER mode disappears. Hints: After replacing batteries or a power failure happens, time setting should be reset. Remote controller possesses memory function, when use TIMER mode next time, just press SET button after mode selecting if time setting is the same as previous one. According to the Time setting sequence of TIMER ON or TIMER OFF, either Start-Stop or Stop-Start can be achieved.
WEEE
In accordance with the directive 2002/96/CE of the European parliament, herewith we inform the consumer about the disposal requirements of the electrical and electronic products.
DISPOSAL REQUIREMENTS:
Your air conditioning product is marked with this symbol. This means that electrical and electronic products shall not be mixed with unsorted household waste. The filled out label must be adhered in the proximity of the product charging port (e. g. A contains fluorinated greenhouse gases covered by the Kyoto Protocol B factory refrigerant charge of the product: see unit name plate C additional refrigerant amount charged in the field D total refrigerant charge E outdoor unit F refrigerant cylinder and manifold for charging
5
Maintenance
For Smart Use of The Air Conditioner
Setting of proper room temperature
Proper temperature
Do not block the air inlet or outlet
Remote Controller
Indoor Body
Do not usewater, wipe the controller with a dry cloth. Do not use glass cleaner or chemical cloth.
wipe the air conditioner by using a soft and dry cloth. For serious stains, use a neutral detergent diluted with water. Wring the water out of the cloth before wiping, then wipe off the detergent completely.
Do not use the following for cleaning Close doors and windows during operation
Use the timer effectively
Gasoline, benzine, thinner or cleanser may damage the coating of the unit. Hot water over 40 O C(104O F) may cause discoloring or deformation.
During cooling operation prevent the penetration of direct sunlight with curtain or blind
Air Filter cleaning
Open the inlet grille by pulling it upward. Remove the filter.
Push up the filter's center tab slightly until it is released from the stopper, and remove the filter downward.
If the unit is not to be used for a long time, turn off the power supply main switch.
Use the louvers effectively
Clean the filter.
Use a vacuum cleaner to remove dust, or wash the filter with water. After washing, dry the filter completely in the shade.
Attach the filter.
Attach the filter correctly so that the "FRONT" indication is facing to the front. Make sure that the filter is completely fixed behind the stopper. If the right and left filters are not attached correctly, that may cause defects.
OFF
Once every two weeks
Close the inlet grille.
Replacement of Air Purifying Filter
1. Open the lnlet Grille
Prop up the inlet grille by using a small device named grille-support which located in the right side of the indoor unit.
4. Attach the standard air filter
(Necessary installation)
ATTENTION:
The white side of the photocatalyst air purifying filter face outside, and the black side face the unit The green side of the bacteria-killing medium air purifying filter face outside, and the white side face the unit.
2. Detach the standard air filter
Slide the knob slightly upward to release the filter, then withdraw it.
5. Close the Inlet Grille
Close the Grille surely Detach old Air Purifying Filter
NOTE:
The photocatalyst air purifying filter will be solarized in fixed time. The bacteria-killing medium air purifying filter will be used for a long time, no need for replacement. But in the period of using them , you should remove the dust frequently by using vacuum cleaner or flaping them lightly, otherwise , its performance will be affected. Please keep the bacteria-killing medium air purifying filter in the cool and dry conditions avoid long time directly sunshine when you stop using it, or its ability of sterilization will be reduced.
3. Attach Air Purifying Filter
Put air purifying filter appliances into the right and left filter frames.
6
Cautions
WARNING
Please call Sales/Service Shop for the Installation. Do not attempt to install the air conditioner by yourself because improper works may cause electric shock, fire, water leakage.
WARNING
When abnormality such as burnt-small found, immediately stop the operation button and contact sales shop. [. . . ] After installation, the power plug should be easily reached.
In dry mode, fan speed can't be changed.
6. The appliance is not intended for use by young children or infirm persons without supervision. Young children should be supervised to ensure that they do not play with the appliance. Please employ the proper power plug, which fit into the power supply cord. [. . . ]