User manual HASSELBLAD FLEXTIGHT 343

[. . . ] is connected to power. · Do not place your fingers or any other object into the scanner while it · Before servicing or opening the scanner, the power supply must be · Install the scanner in a location where children can not get to it. It is not sufficient simply to press the on/off button. System Requirements Below are the basic hardware requirements for the PC or Macintosh system to which the scanner is to be connected. For information about the processor, operating system, RAM and harddisk requirements please refer to the "Software Reference" manual, that comes with the FlexColor software. · Screen resolution of 800 x 600 pixels with true colors (24-bits). · FireWire interface User's Guide - Flextight 343 Hardware Reference - Flextight 343 Front Panel 7 Front Panel C D A E B Figure 1: Front panel features of Flextight 343 A Feed Table: place original holders here for scanning. [. . . ] IMPORTANT: Make sure that the wall socket you are planning to use meets the electrical requirements outlined earlier. Note that the power supply may emit a low buzzing sound when plugged in. Turn on your computer and install the FlexColor image scanning software. 3. 6. User's Guide - Flextight 343 English 1. Place the scanner on a table near your computer with the front facing away from you. Make sure that the location you choose meets all environmental - and electrical requirements as described on page 10. 12 Hardware Reference - Flextight 343 Operating the Scanner English F A B FLEXTIGHT ORIGINAL HOLD ER G H C PATENT PEND ING J à D E Figure 4: Operating the Flextight 343 scanner User's Guide - Flextight 343 Hardware Reference - Flextight 343 Operating the Scanner 13 Operating the Scanner (See Figure 4 opposite). It is assumed that the scanner and FlexColor software have been properly installed. Press the power button (G) on the front of the scanner to switch it on. The indicator light (F) button will start flashing green, indicating that no firmware has been downloaded yet. It will be downloaded automatically later when you first run the FlexColor program. The indicator light (F) will stop flashing indicating that firmware has been downloaded to the scanner. Place the original holder with the slotted tab facing into the scanner. The flexible magnetic layer (C) must face upwards and the holder must fit between the guides (A) on both sides of the feed table. Slide the holder gently into the original holder clasp (H) at the scanner entrance. Lift the magnetic layer (C) of the original holder and place your original (E) with the emulsion side up. The original must completely fill the hole with no edges showing and with a minimum overlap of 2mm along each edge. Also, no edges of the original must extend past the outer edges of the holder. Use the grid in the light area (J) of the feed table (B) to help line up the image. The top layer (C) is magnetic, which will hold the original in place. 4. 5. Go to your computer and follow the directions given in the FlexColor software manual to take a preview, make settings, and take the final scan. User's Guide - Flextight 343 English 14 Hardware Reference - Flextight 343 Resolutions Resolutions English True Optical Resolutions The table below shows the true optical resolutions (in ppi) available with each of the original holders. When scanning at one of the resolution settings listed, one pixel in the scanner's image sensor corresponds exactly to one pixel in the final image. If you use a resolution setting other than those listed, then interpolation (resizing) must be applied. Original 24 x 36 36 x 24 60 x 60 60 x 90 60 x 120 Table 1: Resolutions (PPI) Max. [. . . ] Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. User's Guide - Flextight 343 English 22 Hardware Reference - Flextight 343 CE - Declaration of Conformity CE - Declaration of Conformity English HASSELBLAD A/S HEJREVEJ 30 DK - 2400 COPENHAGEN NV TELEPHONE +45 7026 0800 TELEFAX +45 7026 0900 REG. /VAT NO. 18635445 www. hasselblad. com Declaration of conformity Application of Council Directives: . . . . . . . . . . . . . . . . . Standards to which Conformity is declared: EN61000-6-1 2001, EN61000-6-3 2001 and EN60950:2000. Manufacturer: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Hasselblad A/S Hejrevej 30 DK-2400 Copenhagen NV/ Denmark Type of Equipment: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]