User manual HASSELBLAD FLEXTIGHT 848

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual HASSELBLAD FLEXTIGHT 848. We hope that this HASSELBLAD FLEXTIGHT 848 user guide will be useful to you.


HASSELBLAD FLEXTIGHT 848 : Download the complete user guide (624 Ko)

You may also download the following manuals related to this product:

   HASSELBLAD FLEXTIGHT 848 (1488 ko)
   HASSELBLAD FLEXTIGHT 848 (1485 ko)
   HASSELBLAD FLEXTIGHT 848 (1477 ko)
   HASSELBLAD FLEXTIGHT 848 (1461 ko)
   HASSELBLAD FLEXTIGHT 848 DATASHEET (292 ko)
   HASSELBLAD FLEXTIGHT 848 DATASHEET (415 ko)
   HASSELBLAD FLEXTIGHT 848 DATASHEET (207 ko)
   HASSELBLAD FLEXTIGHT 848 DATASHEET (300 ko)

Manual abstract: user guide HASSELBLAD FLEXTIGHT 848

Detailed instructions for use are in the User's Guide.

[. . . ] is connected to power. · Do not place your fingers or any other object into the scanner while it · Before servicing or opening the scanner, the power supply must be · Install the scanner in a location where children can not get to it. It is not sufficient simply to press the on/off button. User's Guide - Flextight 848 Hardware Reference - Flextight 848 System Requirements 7 System Requirements Below are the basic hardware requirements for the PC or Macintosh system to which the scanner is to be connected. For information about the processor, operating system, RAM and harddisk requirements please refer to the "Software Reference" manual, that comes with the FlexColor software. · Screen resolution of 800 x 600 pixels with true colors (24-bits). · FireWire interface. User's Guide - Flextight 848 English 8 Hardware Reference - Flextight 848 English User's Guide - Flextight 848 Hardware Reference - Flextight 848 Front Panel 9 Front Panel A D E F B C Figure 1: Front panel features of Flextight 848 A Feed Table: must be in lower position for normal scanning. [. . . ] The green light (G) will stop flashing indicating that firmware has been downloaded to the scanner. Select the original holder (K) that matches your original: · For transparencies, choose one of the holders that has a square hole in it. Also, no edges of the original must extend past the outer edges of the holder. · For reflectives, select the large A4/letter-size holder with the clear plastic layer. · For 35 mm slide frames use the optional 35 mm slide mount holder. This is obtained by lifting the table slightly upwards while pushing it gently into the scanner. Please note that when scanning 35 mm slide frames in the 35 mm slide mount holder it is recommended to use autofocus. continues. . . 4. 5. User's Guide - Flextight 848 English 16 Hardware Reference - Flextight 848 Operating Instructions English CLOSED HORIZONTAL NORMAL D A E F G FLEX TIG HT à H J OR IGINA L HO LD ER PATE NT PE ND ING à L K B C Figure 4: Operating the Flextight 848 scanner User's Guide - Flextight 848 Hardware Reference - Flextight 848 Operating Instructions 17 . . . continued NOTE!Each original holder has it's own unique identification code (a combination of small rectangular holes at the holder's leading edge). These codes, combined with the scanner's ability to detect the feed table position, ensure that the scanner will not operate unless the feed table position matches the selected original holder. Place the original holder (K) with the slotted tab facing into the scanner. Make sure that the original holder fits between the appropriate guides (C) or (D) on both sides of the light table. Original 35 mm Portrait 35 mm Landscape 45 x 60 mm Portrait 60 x 60 - 60 x 70 mm 4" x 5" Portrait 13 x 18 Portrait A4 Portrait Table 1: True Resolutions Max. 8000 5000 4000 3200 2040 1600 960 User's Guide - Flextight 848 English 20 Hardware Reference - Flextight 848 Calibrating the Scanner Calibrating the Scanner English The scanner requires two types of calibration: · Focus calibration adjusts the positioning of the scanners optics for each zoom level. If your scans are coming out unfocused or at slightly the wrong size, then you may need to make a new focus calibration to adjust the zoom mechanism. The focus calibration is stored in the scanners flash PROM, so it is preserved when you move the scanner to a new computer. During calibration, the scanner scans a white target to establish the white point along the full length of the scanners CCD. The results of the white calibration scan are saved on your computers hard disk, so you must make a new white calibration if you move the scanner to a new computer. See "White Calibration for Reflectives" on page 22 for more information. · White calibration is only required for reflective scans (it is done Both of the calibration procedures are simple and are initiated from the FlexColor program. User's Guide - Flextight 848 Hardware Reference - Flextight 848 Calibrating the Scanner 21 Focus Calibration The Flextight 848 scanner uses an adjustable zoom and focus mechanism to optimize its scanning resolution for each of the original formats it can handle. If you suspect your scans are not as sharp as they should be, then you may need to calibrate your scanner. It is intended that the scanner is calibrated not more than once every three months. It is a 8 x 9 cm (3" x 3. 5") square of transparent film with a black image on it. Focus sheet PN:40900026, rev. [. . . ] Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. User's Guide - Flextight 848 English 30 Hardware Reference - Flextight 848 CE - Declaration of conformity CE - Declaration of conformity English HASSELBLAD A/S HEJREVEJ 30 DK - 2400 COPENHAGEN NV TELEPHONE +45 7026 0800 TELEFAX +45 7026 0900 REG. /VAT NO. 18635445 www. hasselblad. com Declaration of conformity Application of Council Directives: . . . . . . . . . . . . . . . . . Standards to which Conformity is declared: EN61000-6-1 2001, EN61000-6-3 2001 and EN60950:2000. Manufacturer: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Hasselblad A/S Hejrevej 30 DK-2400 Copenhagen NV/ Denmark Type of Equipment: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE HASSELBLAD FLEXTIGHT 848




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual HASSELBLAD FLEXTIGHT 848 will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.