User manual HAWKE 501-453-UNIV EXD IIC-EXE II-EXTD ASSEMBLY AI300 ISSUE N 09-09

[. . . ] Assembly Instructions for cable gland: 501/453/UNIV Exd IIC/Exe II/ExtD Operating temperature range -60°C +80°C 1 2 International Assembly Instructions AI 300 / Issue N - 09/09 Certification Details Gland Type: 501/453/UNIV Exd IIC/Exe II/ExtD Baseefa06ATEX0057X II 2 GD A21 IP66 IECEx BAS06. 0014X CEPEL-EX-063/2001X GOST R No: POCC GB. 05. B01831 CSA No: 1015065 (LR 78713-7) CNEx07. 0900X 3 4. 1 Reversible Armour Clamping Ring (RAC) General identification ring orientation for: SWA Position Braid 'X', Flat Steel Wire 'Y', Steel Tape 'Z' Ring Position 4 5 1. 4. 1 5. Backnut Middle Nut Reversible Armour Clamping Ring (RAC) Diaphragm Seal / Armour Spigot Cable Guide Entry (with captive deluge seal) IMPORTANT: The arrowhead indicating the correct armour thickness or type should point towards the equipment Note: Cable acceptance sizes are marked on the diaphragm seal, clamping ring and backnut. Cable Preparation Gland Preparation Armour / braid II 4. 1 4 5 I I 4 3 2 1 3 2 Note: Tape armour must be re-trimmed at 90° to the vertical axis of the cable after it has been spread, to ensure that the full face is correctly presented. Roll back option 3 1 2 Shroud option 1 A Strip cable to suit equipment as shown above and expose the armour / braid 'I'. [. . . ] Registered Office: Mitre House, 160 Aldersgate Street, London EC1A 4DD. A member of the Hubbell Group of Companies Hawke International UK Office Oxford Street West, Ashton-Under-Lyne, Lancashire OL7 0NA. UK www. ehawke. com Sales: +44 (0) 161 830 6698 Technical: +44 (0) 161 830 6697 Fax: +44 (0) 161 830 6648 E-mail: sales@ehawke. com 5mm minimum recommended 5 5 4 3 2 5 2 1 2 1 1 D Hold the entry in position with a spanner / wrench to prevent rotation. Hand tighten the middle nut to the entry and turn a further 1/2 to 3/4 of a turn with a spanner / wrench. To ease wiring inside the enclosure, it may be beneficial to strip the inner sheath of the cable as shown above. E Unscrew the middle nut and visually inspect that the armour / braid has been successfully clamped between the diaphragm seal / armour spigot and the armour clamping ring . If armour / braid not clamped, repeat assembly. F Reassemble middle nut onto the entry component . Tighten up the middle nut until hand tight, then using a wrench / spanner, turn the nut through 1/4 turn. Tighten the backnut to form a seal around the cable, then tighten a further full turn using a wrench / spanner. Ensure that the middle nut does not rotate when tightening the backnut . Note:The deluge seal on this gland locates on assembly and requires no further action. [. . . ] Sealing washer, to offer additional ingress protection of the enclosure at the cable gland entry. Serrated washer, to dampen any vibrations that may loosen the locknut or cable gland assembly. AI 300 - Issue N / Page 2 of 2 [. . . ]