User manual HITACHI POWER TOOLS DUT13 ELECTRIC TOOL PARTS LIST

[. . . ] 4 Accessories and Attachments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Carton Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Know Your Drill Press . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Glossary of Terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Place the column (2) on the base, aligning the holes in the column support with the holes in the base. Tighten with an adjustable wrench. 6 7 2 1 INSTALLING BATTERY FOR LASER GUIDE (Fig. Locate the table crank (1) and support lock (2) from the loose parts bag. Insert the support lock handle from the left to right into the hole (3) at the rear of the table support assembly. Install the table crank handle (1) onto the small shaft (4), aligning the set screw (5) with the flat surface of the shaft (4). Tighten the set screw with a hex wrench. NOTE: Replace the batteries with batteries that have a rating of 1. 5 volts (Number 4 series and AAA size or equivalent). When replacing the batteries, the battery guide should be thoroughly cleaned. Use a soft paintbrush or similar device, to remove all sawdust and debris. --11 -- INSTALLING THE HEAD (Fig. G, H and I) WARNING The Drill Press head is very heavy and MUST be lifted with the help of 2 PEOPLE OR MORE to safely assemble the Drill Press head on the column. Carefully lift the head (1) above the column (2) and slide it onto the column. Using the hex wrench, tighten the two head lock set screws (3) on the right side of the head. WARNING Before any assembly of the chuck and arbor to the drill press head, clean all mating surfaces with a nonpetroleum based product; such as alcohol or lacquer thinner. Turn the screw (2) clockwise to eliminate the play, but without obstructing the upward movement of the spindle. N 1 2 2 WARNING To avoid injury from an accidental start, ALWAYS make sure the switch is in the "OFF" position, the switch key is removed, and the plug is not connected to the power source outlet before making belt adjustments. To release the belt tension, turn the belt tension lock knobs (1) on each side of the drill press head counterclockwise. To tighten the belts, push the belt tension handle (2) toward the rear (motor) end. To loosen the belts, pull the belt tension handle (2) toward the front (switch) end. NOTE: Belt tension is correct if the belt deflects approximately 1/2 inch when pressed at its center. WARNING To prevent personal injury, always disconnect the plug from the power source when making any adjustment. O) The quill return spring may need adjustment if the tension causes the quill to return too rapidly or too slowly. Remove from the Hub Assembly; cap, nut, two washers and hub, as shown in Fig. Place a screwdriver in the lower front notch (1) of the spring cap (2). Hold it in place while loosening and removing only the outer jam nut (3). With the screwdriver still engaged in the notch, loosen the inner nut (4) just until the notch (5) disengages from the boss (6) on the drill press head. [. . . ] To return the table to its original position, loosen the bevel locking bolt (3). Gently tap the locking pin until it is seated in the mating hole on the table bracket. Tighten the bevel locking nut against the bracket to hold position. 3. For small pieces that cannot be clamped to the table, use a drill press vise (optional accessory). WARNING The drill press vise MUST be clamped or bolted to the table to avoid injury from a spinning workpiece, or damaged vise or bit parts. [. . . ]