User manual HOLMES HASF2009

[. . . ] If you have any other questions or comments, please write: The Holmes Group, Inc. Box 769, Milford, MA 01757-0769 or visit our website at www. holmesproducts. com For your own records, staple or attach your sales receipt to this manual. Also, please take a moment to write the store name/location and date purchase below. STORE NAME: LOCATION: DATE PURCHASED: (STAPLE RECEIPT HERE) THREE (3) YEAR LIMITED WARRANTY SAVE THIS WARRANTY INFORMATION A. [. . . ] To the extent that any provision of this warranty is inconsistent with any applicable law, such provision shall be deemed voided or amended, as necessary, to comply with such law. 20" Oscillating Power Stand Fan Owner's Guide HASF2009 Fan Blade Cleaning: (See instructions for fan head assembly on page 2, figure 4 ) STEP 1: To access the fan blade, remove the front grill and blade cap. STEP 2: Clean the fan blade, front and rear grills with a soft, moist cloth. STEP 3: Replace blade, tighten blade cap, and securely fasten the front grill. Fan Head, Base, and Pole Cleaning: Using a soft, moist cloth, with or without a mild, soap solution, carefully clean the fan base, pole, and head. Do not allow the motor or other electrical components to be exposed to water. HASF2009KM. 01. US. OM1 HASF200901UM1 Printed In China PLEASE READ AND SAVE THESE IMPORTANT INSTRUCTIONS PLEASE READ AND SAVE THESE IMPORTANT SAFETY INSTRUCTIONS When using electrical appliances, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons, including the following: 1) Read all instructions before using the appliance. 2) To avoid fire or shock hazard, plug the appliance directly into a 120V AC electrical outlet. To avoid fire hazard, NEVER put the cord under rugs, near heat registers, radiator, stoves, or heaters. 4) To protect against electrical hazards, DO NOT immerse in water or other liquids. 5) Close supervision is necessary when any appliance is used by or near children, or by disabled people. 6) Always unplug the fan before moving it, putting on or taking off parts, cleaning, or whenever the fan is not in use. 8) DO NOT operate any appliance with a damaged cord or plug, if motor fan fails to rotate, after the appliance malfunctions, or if it has been dropped or damaged in any manner. Return appliance to manufacturer for examination, electrical or mechanical adjustment, or repair. 9) DO NOT operate in the presence of explosive and/or flammable fumes. THIS PRODUCT IS EQUIPPED WITH A POLARIZED AC (Alternating Current) PLUG (a plug having one blade wider than the other). If it still does not fit, contact qualified personnel to install the proper outlet. DO NOT DEFEAT THE SAFETY PURPOSE OF THIS POLARIZED PLUG IN ANY WAY 10) Use appliance only for intended household use as described in this manual. Any other use not recommended by the manufacturer may cause fire, electric shock, or injury to persons. The use of attachments not recommended or sold by The Holmes Group may cause hazards. 14) WARNING: To reduce the risk of fire or electric shock, DO NOT use this fan with any solid-state speed control device. 15) DO NOT attempt to repair or adjust any electrical or mechanical functions on this unit. All servicing should be performed by qualified personnel only. Figure 1 B A C D E H I J K L M N O F G P A. LOGO PLATE (SNAP ON) FRONT GRILL BLADE CAP FAN BLADE REAR GRILL MOUNTING RING F. FOOT EXTENSIONS (4) Q Pole Assembly: You will need the completed base and extension pole. STEP 1: Remove the base collar from the base by turning counterclockwise. [. . . ] Step 2: Insert the tilt adjustment knob into the neck joint and tighten in place. Figure 4 Base Base Assembly: You will need the base and four extension legs. Push in the small tab on each extension and snap into base. Figure 2 Tilt Adjustment: Follow these instructions to tilt the Fan Head for upward angle air movement. Step 1: To change the tilting angle of the fan head, simply loosen the Tilt Adjustment Knob (see fig. 1). Step 2: Move the fan head to the desired angle, then firmly tighten the knob to lock in place. Fan Head Assembly: You are now ready to assemble the fan head (See Figure #1) Step 1: Position the rear grill over the motor shaft, making certain the 2 notches at the top and bottom of the rear grill fit over the 2 prongs on the motor housing. [. . . ]