User manual HP ALL-IN-ONE 200-5110 GETTING STARTED GUIDE

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual HP ALL-IN-ONE 200-5110. We hope that this HP ALL-IN-ONE 200-5110 user guide will be useful to you.


HP ALL-IN-ONE 200-5110 GETTING STARTED GUIDE: Download the complete user guide (343 Ko)

Manual abstract: user guide HP ALL-IN-ONE 200-5110GETTING STARTED GUIDE

Detailed instructions for use are in the User's Guide.

[. . . ] Getting Started Copyright and License The only warranties for Hewlett-Packard products and services are set forth in the express statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein. HP assumes no responsibility for the use or reliability of its software on equipment that is not furnished by HP. [. . . ] Replace the non-powered speakers with powered speakers. ENWW Speakers and sound 9 Symptom No sound is produced. Possible solution For Windows 7: 1. Click the Start button, click Control Panel, click Action Center, and then click Troubleshooting. Under Hardware and Sound, click Troubleshoot and audio playback. If you use an HDMI connector on the graphics card (select models only) to connect your monitor to the computer, you should also connect analog speakers to the computer Audio Line Out connector if you want to hear sound during the initial setup of the computer. If you are using built-in monitor speakers, use the monitor front-panel Volume button to adjust volume. Use the front-panel buttons to enter the onscreen display (OSD) and ensure that audio is enabled and that the volume is set appropriately. Ensure that you connected powered (active) speakers and that they are turned on. Ensure that the speakers are connected to an audio connector, not a Line In or headphone connector. To resume from Sleep mode, press the Sleep button (select models only), or press Esc. Unplug headphones if they are connected to your computer (or speaker system). Internet access Symptom Internet programs do not start automatically. Possible solution Log in to your ISP, and start the desired program. For Windows 7: 1. Click the Start button, click Control Panel, click Action Center, and then click Troubleshooting. Under Network and Internet, click Connect to the Internet. Verify that you are using the proper cables for your Internet connection type. Your computer might have a dial-up modem and an Ethernet network adapter (also called a network interface card, or NIC). A modem uses a standard telephone cable, whereas the network adapter uses a network cable, to connect to a local area network (LAN). Do not connect a telephone cable to the network adapter, and do not plug a network cable into a telephone service line; doing so might damage the network adapter. 10 Chapter 3 Troubleshooting and maintenance ENWW Symptom Possible solution Run the wireless setup wizard: 1. Click the Start button, click Control Panel, click Network and Internet, and then click Network and Sharing Center. In the Network and Sharing Center window, click Set up a connection or network to open the wizard, and then follow the onscreen instructions. If your system has an external antenna, try to move the antenna to a better position. Try to connect again later, or contact your Internet service provider (ISP) for assistance. Software troubleshooting Some software repairs are as simple as restarting your computer, and others require performing a System Recovery from files on your hard disk drive. To repair software problems, try these methods: Turn the computer off completely and then turn it on again. Use Microsoft System Restore (see Microsoft System Restore on page 12) -- Restore your computer to a configuration that was in use before the software was installed. (See Software program and hardware driver reinstallation on page 13) -- Restores the software (if it came with the product) or hardware driver to factory defaults. System Recovery (see System Recovery on page 16) -- Erase and reformat the hard disk drive, and then reinstall the operating system, programs, and drivers. This erases all data files you have created. ENWW Software troubleshooting 11 Updating drivers A driver is a software program that enables your computer to communicate with an attached device, such as a printer, hard disk drive, mouse, or keyboard. Complete the following procedure to update a driver, or to revert to an earlier version of the driver if the new one does not solve your problem: 1. [. . . ] Click Finish to restart the computer. Recovery discs You should create a set of recovery discs from the recovery image stored on your hard disk drive. This image contains the operating system and software program files that were originally installed on your computer at the factory. You can create only one set of recovery discs for your computer, and the discs can be used only with this computer. Store the recovery discs in a safe place. NOTE: Windows. Some features might not be available on systems that are shipped without a version of Microsoft 18 Chapter 3 Troubleshooting and maintenance ENWW Choosing recovery discs To create recovery discs, your computer must have a DVD writer, and you must use only high-quality blank DVD +R or DVD-R discs. NOTE: You cannot use CDs or DVD+RW, DVD-RW, DVD+RW DL, DVD-RW DL, DVD+R DL, or DVD-R DL discs to create recovery discs. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE HP ALL-IN-ONE 200-5110




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual HP ALL-IN-ONE 200-5110 will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.