User manual HP XP8010 XP8000 DIGITAL PROJECTOR

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual HP XP8010. We hope that this HP XP8010 user guide will be useful to you.


HP XP8010 XP8000 DIGITAL PROJECTOR: Download the complete user guide (181 Ko)

You may also download the following manuals related to this product:

   HP XP8010 (3456 ko)
   HP XP8010 (2435 ko)
   HP XP8010 (4761 ko)

Manual abstract: user guide HP XP8010XP8000 DIGITAL PROJECTOR

Detailed instructions for use are in the User's Guide.

[. . . ] 16 RS-232 protocol reference 3 4 RS-232 protocol reference RS-232 Protocol Reference RS-232 connections This guide describes how to configure the projector for RS-232 communication with an external controller, and describes the RS-232 command keywords used to send requests to the projector. Cable connections Use an RS-232 cable to connect a controller to the projector's D-sub 9-pin connector. The table below lists the connector's pin outputs. When connecting a computer to the projector, use a null-modem cable. D-Sub 9-Pin Connection Pin 3 2 5 Signal TxD RxD GND Direction data from projector to controller data from controller to projector -- Communication settings Make sure the controller device uses the following settings for RS-232 communication with the projector. 9600 baud 1 start bit + 8 data bits (D0 = LSB, D7 = MSB) + 1 stop bit no parity full duplex communication channels (no flow control) no handshaking RS-232 protocol reference 5 RS-232 protocol syntax The following describes the general elements of RS-232 protocol syntax. For details about a specific keyword, refer to the "RS-232 keyword listing" on page 10. [. . . ] For example, if BRT is set to 100 (its maximum): Request: Notification: *BRT=+<CR> *BRT=100<CR><LF> Attempts to modify a read-only setting. Ignores the request, and echoes the keyword with the current value for the setting: Request: Notification: *STAT=3<CR> *STAT=1<CR><LF> 8 RS-232 protocol reference Example -- changing input source The following simplified example shows how the projector typically responds to a request to change the active input source. Request: Notifications: *RSRC=2<CR> *RSRC=2<CR><LF> *SRC=0<CR><LF> (acknowledges request) (projector is attempting to acquire source 2, and in the interim has no valid source) (source 2 has been acquired and is now active) (brightness has been modified for source 2) (color space is not supported for this input) *SRC=2<CR><LF> *BRT=50<CR><LF> *CSPC=?<CR><LF> Example -- changing the picture mode A request to change the picture mode can take a moment to complete, and so produces a delayed notification. Request: Notifications: *PMOD=1<CR> *PMOD=0<CR><LF> *PMOD=1<CR><LF> Example -- turning on the projector Request: Notification: Request: Notifications: *STAT=?<CR> *STAT=0<CR><LF> *W<CR> *W<CR><LF> *STAT=2<CR><LF> *STAT=1<CR><LF> (echoes request) (projector enters its warm-up state) (projector enters its on state) (current setting) (current setting) (new mode is active) RS-232 protocol reference 9 RS-232 keyword listing The following table shows the RS-232 keywords supported by the projector. If the parameter listing for a particular keyword is "None, " that keyword requires no parameter. listing, each Except as noted in the keywordnot warm-up, keyword is valid only when the projector is in its on state, STAT=1 (and cool-down, or standby state). RS-232 keyword listing Keyword SRC Parameters ? Description Queries the current active input source: · 0 = no active source · 1 = VGA1 · 2 = VGA2 · 3 = composite video · 4 = S-video · 5 = component video YPbPr · 6 = RGBHV · 7 = M1 graphics Source functions RSRC 1 to 7, ? Attempts to use the specified source as the active input source, or queries the last source requested: · 1 = VGA1 · 2 = VGA2 · 3 = composite video · 4 = S-video · 5 = component video YPbPr · 6 = RGBHV · 7 = M1 graphics If the requested source is not available and AUTO is enabled, the projector scans for the next valid source; if AUTO is disabled, the projector returns the notification *SRC=0. Queries or sets input source auto-search: 0 = disabled, 1 = enabled 10 RS-232 protocol reference RS-232 keyword listing (continued) Keyword CSPC Parameters 0 to 2, ? Description Sets or queries the active color space: 0 = RGB, 1 = YPbPr, 2 = YCbCr Note: The active input source must be analog RGBHV interlaced, analog RGBHV progressive, or component progressive. Video functions PMOD 0 to 2, ? Sets or queries the picture mode: · 0 = business graphics mode · 1 = theatre video mode · 2 = super-bright mode Note: The notification sent in response to a request using PMOD indicates the current picture mode, not the requested picture mode. Once it does, a second notification is sent indicating that the requested picture mode is active. WHIT BRT CON SAT TNT CTMP SHRP KEYV 0 to 10, +, ­, ?Sets or queries the color temperature: 0 = warm, 1 = neutral, 2 = cool Sets or queries the sharpness. Sets or queries the vertical keystone: · 0 = no keystone adjustment. · ­1 to ­50: shrinks the bottom of the display. RS-232 protocol reference 11 RS-232 keyword listing (continued) Keyword KEYH Parameters ­50 to 50, +, ­, ? Description Sets or queries the horizontal keystone: · 0 = no keystone adjustment. · ­1 to ­50: shrinks the left side of the display. ASPT 0 to 3, ? Sets or queries the aspect ratio: · 0 = 1-to-1 · 1 = Best Fit · 2 = Fill · 3 = 16:9 Note: All options may not be available for all input sources. Sets or queries horizontal panning of zoomed images: · 0 (lower limit) = the left edge of the window aligns with the left edge of the screen. · 100 (upper limit) = the right edge of the window aligns with the right edge of the screen. Sets or queries vertical panning of zoomed images: · 0 (lower limit) = the top edge of the window aligns with the top edge of the screen. · 100 (upper limit) = the bottom edge of the window aligns with the bottom edge of the screen. SYNC None Automatically resynchronizes (auto-sync) the projector to the active input source. Note: The active input source must be VGA1, VGA2, analog M1, or analog RGBHV. Sets or queries the projector's position: · 0 = front table · 1 = front ceiling VERS ? [. . . ] The projector sends a notification when it enters warm-up state (STAT=2), and another when it enters the on state (STAT=1). Note: This keyword requires the projector to be in standby state (STAT=0). Note: Do not send any requests other than STAT in the time between the warm-up and on state notifications. Otherwise, unexpected results can occur. RS-232 protocol reference 15 RS-232 keyword listing (continued) Keyword STAT Parameters ? Description Queries the projector's current state: · 0 = standby state · 1 = on · 2 = warm-up state · 3 = cool-down state Note: STAT can be used anytime, regardless of the projector's state. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE HP XP8010




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual HP XP8010 will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.