User manual HUAWEI QUIDWAY 3600

[. . . ] HUAWEI® Quidway R2600/3600 Series Modular Routers Installation Manual V200R001 Quidway R2600/3600 Series Modular Routers Installation Manual Manual Version Product Version BOM T2-080430-20020202-C-1. 0 V200R001 31040430 Copyright © 2001 by Huawei Technologies Co. , Ltd. All Rights Reserved No part of this document may be reproduced or transmitted in any form or by any means without prior written consent of Huawei Technologies Co. , Ltd. Trademarks ® , HUAWEI®, C&C08, EAST8000, HONET, ViewPoint, INtess, ETS, DMC, SBS, TELLIN, InfoLink, Netkey, Quidway, SYNLOCK, Radium, , M900/M1800, TELESIGHT, Quidview, NETENGINE, Musa, OptiX, Airbridge, Tellwin, Inmedia, VRP, DOPRA, iTELLIN are trademarks of Huawei Technologies Co. , Ltd. Notice The information in this document is subject to change without notice. Although every effort has been made to make this document as accurate, complete, and clear as possible, Huawei Technologies assumes no responsibility for any errors that may appear in this document. Huawei Technologies Co. , Ltd. Address: Zip code: Tel: Fax: Website: E-mail: Huawei Customer Service Building, Kefa Road, Science-based Industrial Park, Shenzhen, P. China 518057 +86-755-6540036 +86-755-6540035 http://www. huawei. com support@huawei. com About This Manual Contents The manual consists of 8 chapters that brief the appearance, features, installation, configuration, maintenance, troubleshooting and function modules of Quidway R2600/3600 Series Modular Routers. Chapter 1 is a brief introduction of the Quidway R2600/3600 series modular routers. [. . . ] [M] Press <Enter>, and the following prompt will be given: For each of the following questions, you can press <Return> to select the value shown in braces, or you can enter a new value. The above prompt indicates that the following options have default values (those contained in [ ] are default values). If there is no need to modify the value, press <Enter>; or, enter a new value. NETWORK INTERFACE PARAMETERS: Do you want a LAN1 interface?[255. 255. 0. 0] HARDWARE PARAMETERS: Baud rate for serial channels [9600] NETUTILS APPLICATION PARAMETERS: IP address of the TFTP Boot server to boot from?[10. 110. 200. 1]" must be the IP address of the PC connected with the Ethernet. After entering the last value, the following prompt will be given, requesting you to confirm the input values: ------------------------------------------------------------------NETWORK INTERFACE PARAMETERS: IP address on LAN1 is 10. 110. 10. 10 LAN1 interface's subnet mask is 0xffff0000 HARDWARE PARAMETERS: Serial channels will use a baud rate of 9600 NETUTILS APPLICATION PARAMETERS: IP address of the TFTP host is 10. 110. 10. 13 The file to download and start is ram. abs After board is reset, start-up code will wait 2 seconds ------------------------------------------------------------------(M)odify any of this or (C)ontinue?[M] Step 4: Enter <C> to confirm the above selection, and BOOTROM will be normally started. Step 5: Enter <2> in the BOOT menu, and download the application program via TFTP, and the following prompt will be displayed: Please start TFTP server then press ENTER key to get start If the PC running the TFTP Server is ready, press <Enter> to start the loading. Starting the TFTP download. . . Press ENTER key to reboot the system. 6-5 Installation Manual Quidway R2600/3600 Series Modular Routers Chapter 6 Maintenance The loading is successful. Press <Enter>, and the router will be rebooted. Caution: Please do not upgrade the software system of the router rashly. If necessary, upgrade under the guidance of technical support engineer. 6. 1. 4 Uploading and Downloading Files via FTP R2600/3600 series can serve as the FTP server and enable you to update configuration and program files. Any FTP client can be connected to the router, and be used to upload and download the configuration and program files after passing user authentication. Note: Uploading: Transferring files to the router from the PC running FTP, which is connected to the Ethernet interface of the router. Downloading: Transferring files from the router to the PC running FTP, which is connected to the Ethernet interface of the router. I. Starting the FTP server on the router 1) Set the authentication In global mode, enter <aaa-enable>. In global mode, enter <aaa accounting optional>. Note: For details of the above commands, please refer to Chapter 1 AAA Configuration and RADIUS Configuration in 07 Security Configuration of VRP User Manual - Configuration Guide (V1. 5). 2) Add username and password In global mode, enter <user ftp password 0 123 service-type ftp> is entered, it indicates that the username is ftp and the password is 123. 3) Start the FTP server In global mode, enter <ftp-server enable>. With the above operations, the FTP server is started and the username is set. So any FTP client program can log in the FTP server with this username and password. 6-6 Installation Manual Quidway R2600/3600 Series Modular Routers Chapter 6 Maintenance II. Uploading configuration file Configure the Ethernet interface address of the router to connect the host running the FTP client program to the router. Log in the FTP server with the username and password already set in the router. Take the FTP client program provided by Windows 98 as an example: With the DOS prompt, enter <FTP A. B. C. D> (A. B. C. D is the IP address on the Ethernet interface of the router). Under the "username" prompt, enter the username <ftp>. Under the "password" prompt, enter the password <123>. [. . . ] If WAN is dialup line, connect the cable to the serial port of analog Modem. Step 3: Power on the router and check the status of READY indicator on the corresponding slots on the front panel of the router. If the indicator is On, it means module has passed self-test and can start normal work. Step 4: Power on the router and check the status of LINK indicator of 8LSA. [. . . ]