User manual HUSKY HU80520

[. . . ] OPERATOR'S MANUAL GASOLINE PRESSURE WASHER HU80520 Your pressure washer has been engineered and manufactured to Husky's high standard for dependability, ease of operation, and operator safety. When properly cared for, it will give you years of rugged, trouble-free performance. WARNING: To reduce the risk of injury, the user must read and understand the operator's manual before using this product. Thank you for your purchase. SAVE THIS MANUAL FOR FUTURE REFERENCE TABLE OF CONTENTS Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Keep away from ignition sources, handle outdoors only, do not smoke while adding fuel, and wipe up spills immediately. When adding gas to the pressure washer, make sure the unit is sitting on a flat, level surface. Insert a clean funnel into the fuel tank then slowly pour gasoline into the tank. Clean up any spills before starting the engine. FUNNEL FUEL CAP Fig. Before detergent can be used with this machine, the injection hose must be attached. Push the open end of the clear injection hose securely over the fitting as shown in figure 7. Place the filtered end of the injection hose in the bottle of detergent. INJECTION HOSE FITTING ASSEMBLING THE SPRAY WAND See Figure 7. To attach the spray wand extension: Place the threaded end of the wand extension in the connector on the end of the spray wand assembly. When not in use, remove the spray wand extension from the spray wand by turning the connector counter clockwise. 6 SPRAY WAND CONNECTING HIGH PRESSURE HOSE TO SPRAY WAND ASSEMBLY See Figure 8. Screw the collar on the high pressure hose into the spray wand's inlet coupler by turning the hose collar clockwise. Pull on the hose to be certain it is properly secured. CONNECTOR GROOVED GRIPPING SURFACE SPRAY WAND EXTENSION Fig. 8 11 ASSEMBLY CONNECTING THE HIGH PRESSURE HOSE TO THE PUMP See Figure 9. After the high pressure hose has been uncoiled and attached to the spray wand: Align the collar on the threaded nipple on the pump. Insert the nozzle on the end of the high pressure hose collar into the threaded nipple. COLLAR CONNECTING THE GARDEN HOSE TO THE PRESSURE WASHER See Figure 10. Before connecting the garden hose to the pressure washer: Run water through the hose for 30 seconds to clean any debris from the hose. If the screen is damaged, do not use the machine until the screen has been replaced. If the screen is dirty, clean it before connecting the garden hose to the machine. NOTE: There must be a minimum of 10 feet of unrestricted hose between the pressure washer intake and the hose faucet or shut off valve (such as a "Y" shut off connector). With the hose faucet turned completely off, attach the end of the garden hose to the water intake. 10 OPERATION WARNING: Do not allow familiarity with tools to make you careless. [. . . ] to be defective in material or workmanship will be repaired or replaced, without charge for parts and labor, by an Authorized Service Center for HUSKY® brand pressure washers (Authorized HUSKY® Service Center). The product, including any defective part, must be returned to an Authorized HUSKY® Service Center within the warranty period. The expense of delivering the product to the service center for warranty work and the expense of returning it back to the owner after repair or replacement will be paid for by the owner. Techtronic Industries North America, Inc. 's responsibility in respect to claims is limited to making the required repairs or replacements and no claim of breach of warranty shall be cause for cancellation or rescission of the contract of sale of any HUSKY® brand pressure washer. [. . . ]