User manual IOMEGA JAZ 1GO INTERNE
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual IOMEGA JAZ 1GO INTERNE. We hope that this IOMEGA JAZ 1GO INTERNE user guide will be useful to you.
Manual abstract: user guide IOMEGA JAZ 1GO INTERNE
Detailed instructions for use are in the User's Guide.
[. . . ] 1-801-778-5763 Automated E-Mail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . support@iomega. com (Please type "Jaz" in the subject header when sending your E-Mail) Iomega Bulletin Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-801-778-5888 8, N, 1; 9600 baud and above; ANSI (24 hrs - Download only) Repair and Return Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] (Refer to your computer manual if removal is unclear. )
Locate a vacant 31/2-inch or 51/4-inch drive bay. See notes in illustration for the next step.
Instructions for assembling the mounting bracket are printed on the box.
Use the 3. 5" Universal Installation Kit to assemble a 5. 25" mounting bracket and attach it to the drive, then go to step 6.
51/4-inch drive bays ONLY:
Disconnect power
51/4-inch Bay (after selecting bay, go to step 5a)
A 2 ta tta 3 A b ch S tta fir th bo lid ch st e , 4 as ttoe th th le A se mth e en ft e dr lig m D ra ho di C re il N bo iv n bl th y. le sk cape 1 th O th e s dr at to as e bl ho e TE cl di V of iv e pr th w br : 6 ip pi sk er th e e ct 4 oc ify ev ac S ta ur dr e in on esfa to ce er ke cr bs ed iv th di s T ts ew en . e at sk po to fo pl H to s re th at ga S tano dr sitio e r e IS th th w lig iv IS e er ge ht in ga e n, co e 3 in in N di e th ly g ps with al nn rig se O sk pr e fle cl ar ig ec ht rt T dr ov sl ni x ip e po ngto ra bo A iv id ot th r il 5 pr st N e ed s e ov es s th of tto on E if dr er en of e th m C dein E th e th th iv S si is e e th t on e di S re cl e sk A d, ki bo ip ce th br ac dr R t tto an nt e to Y ke iv m d er fa S e. n un til
G B
6 7
Check mounting requirements: Your drive bay may require side rails. See your computer dealer for any special hardware. )
13
Good job!Now check all connections, arrange the cables to fit under the cover, and replace the computer cover.
Reconnect power
Slide the Jaz drive into the drive bay.
31/2-inch Installations IMPORTANT!If your Jaz drive will be part of a SCSI chain, check the SCSI ID BEFORE sliding the drive into the drive bay. (See Jaz User's Guide. ) 51/4-inch Installation
14 15
Reconnect power cord, turn ON power switch, and wait for DOS or Windows to come up. Gently insert the 1GB Jaz "tools" disk into the Jaz drive.
The drive status light on the Jaz drive flashes as the disk spins up and glows steadily while it acquires. The drive will take a few seconds to spin down and eject the disk.
Disk shown fully inserted
8
Connect a computer power supply cable.
Jaz Drive
If your computer has no spare power supply cable, you will need to use a power Y-cable. Call your dealer or 1-800-MY-STUFF to order.
G B
1
to o ls
1
B G
Power Supply Cable
Drive-Status Light Disk Eject Button
Disk shown ejected from drive
9
Connect the data cable connector that is closest to the termination block to your Jaz drive. (Connector
fits only one way. )
Jaz Drive
CAUTION Never put anything except Jaz disks into the Jaz drive as this could damage your drive.
Pin One If there is more than one internal drive in the SCSI chain, you will need to use a different data cable in order to daisy-chain your internal devices. Cable Connector
16
Insert the Install diskette for your system into your computer's floppy drive.
Use Disk 1 if your computer is running Windows 95, Windows 3. 1, or DOS. Use Disk 2 if your computer is running Windows NT.
Termination Block
10 11
Find the colored stripe (or printing) on one side of the data cable, showing PIN 1.
Stripe or printing shows the PIN-ONE side of the data cable.
W in d o
In ll aS st DO
s/
w
Connect the PIN 1 side of the data cable to PIN 1 on the SCSI adapter (or other SCSI connector). (Check the adapter documentation to
identify PIN 1 position. )
PIN 1 PIN 1
17
Start the Setup or Install program as described below and follow the screen instructions to install your Jaz Tools software.
Windows® 95 Users:
Open My Computer and double click on the floppy drive icon to open a window for Install Disk 1. [. . . ] Avoid deleting the installation files for your system in case you need to reinstall your software.
Some adapters have a keyed connector to help PIN 1 connection.
Some adapters have PIN 1 toward rear of computer.
Some adapters have PIN 1 toward front of computer.
12
Secure drive in drive bay using the screws included in the 3. 5" Universal Installation Kit. (If necessary,
refer to your computer manual for instructions on how to access drive bay mounting holes. )
31/2-inch Drive Bay 51/4-inch Drive Bay with Bracket
Congratulations!When the software installation is complete, your Jaz drive will be ready to use.
Use your Jaz drive just like any other drive on your system. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE IOMEGA JAZ 1GO INTERNE
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual IOMEGA JAZ 1GO INTERNE will begin.