User manual JENSEN VOYAGER JHD1120

[. . . ] 11 ii JHD1120 INTRODUCTION System Features Features of the Jensen JHD1120 mobile audio system include: · · · · · · · · · · · · 10 Character Alpha-Numeric Segmented LCD AM/FM US/EURO Tuner with 30 Presets (12 AM, 18 FM) RBDS (Radio Broadcast Data Service) with PTY Search Weatherband Tuner Mute Pre-set Equalizer - 5 settings (Flat, Rock, Pop, Classical, User) Electronic Bass, Treble, Balance and Fader Controls Output Power 40W x 4 Clock 12/24 Hour Selectable IR Wireless Remote Control Ready (sold separately) 2-Wire Power with Non-Volatile Memory and Clock/Time Support Auxiliary Audio Input (Front 3. 5mm Stereo Jack) Content List · · · · · Jensen Heavy Duty Radio Hardware Kit 15AMP Fuse Installation Manual Quick reference Guide HARDWARE KIT CONTENTS FLANGE NUTS MOUNTING STRAP DIN SLEEVE REMOVAL TOOL MOUNTING BUSHING MOUNTING SCREW 1 JHD1120 SAFETY INFORMATION When Driving Keep the volume level Iow enough to be aware of the road and traffic conditions. When Washing Your Vehicle Do not expose the product to water or excessive moisture. When Parked Parking in direct sunlight can produce very high temperatures inside your vehicle. Use the Proper Power Supply This product is designed to operate with a 12 volt DC negative ground battery system. [. . . ] Press MUTE again to restore the audio output to the previous level. 3 1 12 20 AS/PS DN UP Mode PTY MENU INFO ENTER 16 Press the MODE button (4) to select a different mode of operation, as indicated on the display panel. Tuner is the default source when a prior source is no longer available. TF iPod DISC WB M P3 AM 1 FM 2 SAT 3 ST PS TITLE AR TIST CH. NA ME CA T MEN U LD CO MPOSER R PT IN T RDM ALARMSLEEP JHD1120 40W x 4 Reset The reset button should be activated for the following reasons: · · · initial installation of the unit when all wiring is completed function buttons do not operate error symbol on the display 4 15 11 17 8 6 5 7 9 10 2 13 Power On/Off Press the rotary encoder POWER button (1) to turn the unit on or off. The unit will resume at the last mode selected (Tuner, Auxiliary, etc. ). Use a ball point pen or thin metal object to press the RESET button (20). This may be necessary should the unit display an error code. Audio Menu Press the AUDIO button (3) to access the audio menu. You can navigate through the audio menu items by pressing the AUDIO button repeatedly. Once the desired menu item appears on the display, adjust that option by turning the rotary encoder (1) within 5 seconds. The unit will automatically exit the audio menu after five seconds of inactivity. Bass Level Use the rotary encoder (1) to adjust the Bass level range from "-7" to "+7". Treble Level Use the rotary encoder (1) to adjust the Treble level range from "-7" to "+7". Balance Adjusting Balance controls the relative level between the left and right speakers in each pair. Use the rotary encoder (1) to adjust the Balance between the left and right speakers from "L 12" to "R12". POWER Volume Control To increase the volume, turn the rotary encoder (1) to the right. To decrease the volume, turn the rotary encoder to the left. Fader Adjusting Fade controls the relative level between the front and rear speaker pairs. Use the rotary encoder (1) to adjust the Fader between the rear and front speakers from "R12" to "F12". The maximum volume setting is 40. 5 JHD1120 System Menu 1. · · · · · · Press and hold the PTY/MENU button (2) for more than 2 seconds to enter the system menu. Press the TUNE/SEEK |<< / >>| (18, 19) button repeatedly to navigate the system menu. KEYBEEP (Clk (click) / Bep (beep) / Off): Turn the audible beep On/Off (heard when functions/buttons are selected). P-- CLOCK (1-10 / Off) CLK FMT (12Hour / 24Hour): Select 12 or 24 hour display mode. · Press the INFO/ENTER button (16) to view the clock set screen. · Press the TUNE/SEEK |<< / >>| (18, 19) buttons to adjust the selected digit. BAT ALRM (Off / On): When ON, radio will alert when vehicle battery voltage is below 10. 8 VDC. BAT OFF (Off / On): When ON, radio will automatically turn off when vehicle battery voltage is below 10. 8 VDC. [. . . ] This is a result of the radio being placed close to the ignition system (engine). This type of noise can be easily detected because it will vary in intensity of pitch with the speed of the engine. Usually, the ignition noise can be suppressed considerably by using a radio suppression type high voltage ignition wire and suppressor resistor in the ignition system. (Most vehicles employ this wire and resistor but it may be necessary to check them for correct operation. ) Another method of suppression is the use of additional noise suppressors. [. . . ]