User manual JONSERED CS 2117 EL
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual JONSERED CS 2117 EL. We hope that this JONSERED CS 2117 EL user guide will be useful to you.
You may also download the following manuals related to this product:
JONSERED CS 2117 EL (2796 ko)
JONSERED CS 2117 EL (2952 ko)
JONSERED CS 2117 EL (1509 ko)
JONSERED CS 2117 EL (2796 ko)
JONSERED CS 2117 EL (2796 ko)
JONSERED CS 2117 EL (2796 ko)
JONSERED CS 2117 EL (4021 ko)
JONSERED CS 2117 EL (4021 ko)
JONSERED CS 2117 EL (4021 ko)
JONSERED CS 2117 EL (4021 ko)
JONSERED CS 2117 EL (4021 ko)
JONSERED CS 2117 EL (2952 ko)
JONSERED CS 2117 EL (1509 ko)
JONSERED CS 2117 EL (1509 ko)
Manual abstract: user guide JONSERED CS 2117 EL
Detailed instructions for use are in the User's Guide.
[. . . ] Español Lea atentamente las instrucciones y asegúrese de entenderlas antes de utilizar esta unidad.
545079719
1/3/06
IDENTIFICATION (WHAT IS WHAT?)
Chain Adjustment Tool (Bar Tool) Front Hand Guard Front Handle Starter Rope Idle Speed Screw Chain Muffler ON/STOP Switch Primer Bulb
Bumper Spike
Bar Oil Fill Cap Cylinder Cover
Starter Housing
Fuel Mix Fill Cap
Throttle Lockout Rear Handle
Adjusting Screw
Chain Direction of Travel
Throttle Choke/ Trigger Fast Idle Chain Brake Lever
Chain Catcher
Chain Brake Nuts
Guide Bar
Bar Sprocket Hole
IDENTIFICATION OF SYMBOLS
WARNING!Careless or improper use can cause serious or even fatal injury.
Always wear appropriate ear protection, eye protection and head protection. Read and understand the instruction manual before using the chain saw.
Sound power level
Sound pressure level at 7, 5 meters
WARNING!Contacting the guide bar tip with any object should be avoided; tip contact may cause the guide bar to move suddenly upward and backward, which may cause serious injury.
2
SAFETY RULES
Always disconnect spark plug wire and place wire where it cannot contact spark plug to prevent accidental starting when setting up, transporting, adjusting or making repairs except carburetor adjustments. [. . . ] Chain Brake Nuts
Chain Brake Nuts
Chain Adjustment Tool (Bar Tool)
WARNING: If the saw is operated with a loose chain, the chain could jump off the guide bar and result in serious injury. Do not touch the muffler or allow combustible material such as dry grass or fuel to do so.
Adjusting the tension:
Chain tension is very important. This is especially true during the first few times you use your saw.
OPERATING YOUR UNIT
BEFORE STARTING ENGINE
Oil Cap Fuel mix cap
WARNING: Be sure to read the fuel information in the safety rules before you begin. If you do not understand the safety rules, do not attempt to fuel your unit. Contact an authorized service dealer.
BAR AND CHAIN LUBRICATION
The bar and chain require continuous lubrication. Lubrication is provided by the automatic oiler system when the oil tank is kept filled. Too little oil will cause overheating shown by smoke coming from the chain and/ or discoloration of the bar. Only use Bar and Chain Oil for bar and chain lubrication.
FUELING ENGINE
7
WARNING: Remove fuel cap slowly when refueling. Before operation, gasoline must be mixed with a good quality 2-cycle air-cooled engine oil designed to be mixed at a ratio of 40:1. A 40:1 ratio is obtained by mixing 0, 125 liter of oil with 5 liters of unleaded gasoline. Always read and follow the safety rules relating to fuel before fueling your unit.
IMPORTANT
Experience indicates that alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. The brake is designed to stop the chain if kickback occurs.
S The inertia activated chain brake is activated if the front hand guard is pushed forward, either manually or by centrifugal force. S If the brake is already activated, it is disengaged by pulling the front hand guard back toward the front handle as far as possible. Disengaged Engaged
should be placed on the ground with the engine running. Grip the rear handle with your right hand and the front handle with your left hand. Activate the chain brake by turning your left wrist against the hand guard without releasing your grip around the front handle. The chain should stop immediately.
Inertia activating function control
checked several times daily. This is the only instance when the saw
Braking function control CAUTION: The chain brake must be
WARNING: When performing the following procedure, the engine must be turned off. Grip the rear handle with your right hand and the front handle with your left hand. Hold the chain saw approximately 14" (35 cm) above a stump or other wooden surface. Release your grip on the front handle and use the weight of the saw to let the top of the guide bar fall forward and contact the stump. When the tip of the bar hits the stump, the brake should activate.
CUTTING METHODS
IMPORTANT POINTS
S Check chain tension before first use and after 1 minute of operation. [. . . ] Cylinder Screws Cover Spark Plug Boot Spark Plug
BAR MAINTENANCE
If your saw cuts to one side, has to be forced through the cut, or been run with an improper amount of bar lubrication it may be neces-
12
CHAIN SHARPENING
Chain sharpening is a complicated task that requires special tools. We recommend that you refer chain sharpening to a professional chain sharpener.
STORAGE
CARBURETOR ADJUSTMENTS
WARNING: The chain will be moving during most of this procedure. Adjustments may be necessary if you notice any of the following conditions: S Chain moves at idle. See IDLE SPEED- ad-T justing procedure.
Idle Speed--T
Allow engine to idle. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE JONSERED CS 2117 EL
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual JONSERED CS 2117 EL will begin.