User manual KENWOOD DNX5220

[. . . ] Error Specifications 91 92 94 96 English 3 How to read this manual This manual uses illustrations to explain its operations. The displays and panels shown in this manual are examples used to provide clear explanations of the operations. For this reason, they may be different from the actual displays or panels used, or some display patterns may be different. Seek Mode Sets a station selection. The mode is switched in following order each time you touch the button. Display "AUTO1" "AUTO2" "MANU" Setting Tunes in a station with good reception automatically. [. . . ] 1 Display the Outgoing Calls or Incoming Calls screen / · The Outgoing Calls list screen or Incoming Calls list screen shows the list of the calls originated from or received at this unit. They are not the ones stored in the cell-phone memory. : Outgoing Calls : Incoming Calls The Outgoing Calls or Incoming Calls list screen appears. 2 Select from calls list Example : Outgoing Calls screen 1 3 4 2 5 2 6 1 2 3 4 Outgoing Calls list. 3 Make a call English 49 Hands Free Unit Control Calling by Voice Recognition Calls by recognizing the registered voice. / · In order to perform voice recognition, voice must be registered in the Phonebook data. Or, to perform voice recognition by Phone number category (Home, Office, Mobile etc. ) of Phonebook data, a key word voice must be registered. See <Key Word Voice Recognition> (page 53). If you hear another Beep sound: Speak the key word within 2 seconds after the Beep, or touch the [Phonebook List] button to select the phone number. Make a call. / · If there are more than one phone numbers registered under the same name, and the key word voice is registered for each phone number, you will hear another beep. For how to register key word, see <Key Word Voice Recognition> (page 53). 1 Display the Voice Recognition screen If there are more than one phone numbers registered under the same name, go to step 3. 3 Select a Phone number category 4 6 5 7 2 Utter the voice registered in the PhoneBook 1 2 8 Utter within 2 seconds after the Beep. 4 Make a call If the voice recognition is succeeded and there is only one phone number found: / · A message is displayed if the voice is not recognized. 3 Displays the phonebook list. 50 DNX5220/DNX512EX/DDX512/DDX5032 Setting Up the Hands-Free Phone The Hands-Free system can be set as follows. 1 Display the Hands Free Setup screen 2 Setup each item 1 2 3 4 5 6 5 Sets the beep of the incoming SMS. 4 Search phone number to register with each function 5 Register phone number / · Press [Delete] to delete the registered phone number. 2 Select the Preset number to register 1 1 Returns to the Hands-Free Set Up screen. 3 Select the search destination of the number to register 2 3 9 4 5 6 7 8 10 11 2 3 4 5 6 7 8 Registers from SMS incoming calls list. 54 DNX5220/DNX512EX/DDX512/DDX5032 SMS (Short Message Service) Uses SMS function. 1 Display the SMS Select screen SMS Message screen 10 11 12 13 12 2 Select a function 1 2 p Calls the number in the selected message. 4 Create a message 15 14 14 17 4 5 17 18 19 20 21 22 16 3 1 Displays received message list. s Returns to the previous screen. 6 Calls the number in the selected message. 9 Displays the selected message. English 55 Setup Menu You can set up various receiver parameters. Setup Menu Displays the Setup menu to set various functions. 1 Display the control screen of any source Audio Setup You can setup a speaker network, etc. in the "Setup / · [Audio Setup] cannot be selected under the following conditions: ­ When no source is selected. See <Zone Control> (page 84). Touch any source button on the "Source Select" screen. 2 Display the Setup Menu 2 Setup each item 1 2 3 4 3 Select the setup item 1 2 2 1 The selected setup screen appears. [. . . ] At such times this message will appear. Change the source to any source other than USB/iPod. Connect an USB device/iPod, and change the source to USB/iPod again. No Music: The connected USB device contains no playable audio file. Media was played that doesn't have data recorded that the unit can play. USB Device Error!!: The connected USB device is rated a current capacity higher than the allowable limit. Use the unit again after reducing the temperature inside the vehicle. Hold Error : Activation of the protective circuit when the temperature inside the disc changer is higher than 60 degrees Celsius stops the disc changer from operating. [. . . ]