User manual KENWOOD GRC-151

[. . . ] Saving energy reduces air pollution and lowers utility bills. For the United Kingdom Factory fitted moulded mains plug 1. The fuse cover must be refitted when replacing the fuse in the moulded plug. If the plug fitted is not suitable for the power points in your home or the cable is too short to reach a power point, then obtain an appropriate safety approved extension lead or adapter, or consult your dealer. If nonetheless the mains plug is cut off, remove the fuse and dispose of the plug immediately, to avoid a possible shock hazard by inadvertent connection to the mains supply. *AC voltage selection The AC voltage selector switch on the rear panel is set to the voltage that prevails in the area to which the unit is shipped. [. . . ] Adjust only those controls that are covered by the instruction manual as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the appliance to its normal operation. 16. Servicing ­ The user should not attempt to service the appliance beyond that described in the instruction manual. All other servicing should be referred to qualified service personnel. 17. Outdoor antenna grounding ­ If an outside antenna is connected to the appliance, be sure the antenna system is grounded so as to provide some protection against voltage surges and built up static charges. Article 810 of the National Electrical Code ANSI/ NFPA 70, provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. See Figure. EXAMPLE OF ANTENNA GROUNDING AS PER NATIONAL ELECTRICAL CODE 20. If connections are loose, there could be loss of sound or noise produced. When plugging and unplugging connection cords, be sure to first remove the power cord from the AC outlet. Plugging/unplugging connection cords without removal of the power cord can cause malfunctions or damage to the unit. Do not connect up a power source which is larger than that indicated on the socket at rear of the unit. System connections 7 SYSTEM CONTROL CONNECTIONS Connecting system control cords after connecting a KENWOOD audio component system lets you take advantage of convenient system control operations. SYSTEM CONTROL SYSTEM CONTROL This unit is compatible only with the [SL16] mode. The system control operation is not available if the unit is connected in the [XS-8] connection mode. SYSTEM CONTROL SYSTEM CONTROL (dB) -- --5 0 +3 +6 (dB) TAPE A TAPE B SYSTEM CONTROL ÷ Do this operation after completing all connections. 1 Dolby NR on 2 Dolby NR off Dolby NR on DOLBY NR Dolby NR off DOLBY NR -- --5 0 +3 +6 (dB) Lit Goes off 2 Select the playback mode. (CT-403/KXF-W3030 only) REV. MODE (dB) -- --5 0 +3 +6 (dB) ÷ Each press switches the indication. 1 "[" :Double-side playback which stops tape after having played both sides. 3 """ :One-way playback which stops tape after having played a single side. 2 Start playback. CT-403 /KXF-W3030 @ 7 # CT-401 /GRC-151 or 3 ÷ Tapes are played in the directions indicated by their respective indicators. (CT-403/KXF-W3030) ÷ Playback stops automatically at the end of tape. (CT-401/GRC-151) Listening to cassette tapes 11 To stop playback Fast Forward and Rewind 1 Stop playback. (dB) -- --5 0 +3 +6 (dB) 7 (dB) -- --5 0 +3 +6 (dB) 7 2 Press the 1 key or ¡ key. 1 (dB) ¡ -- --5 0 +3 +6 (dB) ÷ When taking out the tape, press the area marked PUSH/ OPEN 0 after the tape transport has stopped completely. 1: Fast tape winding in the | direction ¡: Fast tape winding in the \ direction ÷ Press the stop (7) key to stop fast tape winding. Relay playback (CT-403/KXF-W3030 only) This function plays back the tapes in both decks A and B continuously and repeatedly. 1 Load cassette tapes in both decks. 2 Determine the playback conditions. 1 Select the Dolby NR mode. DOLBY NR (dB) 0 ÷ Set to OFF the Dolby NR key when playing a tape recorded without using Dolby NR. 1 Dolby NR on 2 Dolby NR off Dolby NR on DOLBY NR Dolby NR off DOLBY NR -- --5 0 +3 +6 (dB) Lit Goes off 2 Select the playback mode. REV. MODE (dB) -- --5 0 +3 +6 (dB) 3 Start playback. (dB) ÷ Each press switches the indication. 1 "[" :Relay playback of two sides of tapes in decks A and B is repeated. 2 """ :Relay playback is not available with this setting. 3 """ :Relay playback of one side only for deck A and deck B, and then playback stops. -- --5 0 +3 +6 (dB) @ 7 # ÷ Tapes are played in the directions indicated by their respective indicators on the display. [. . . ] ¶ Press the desired operation key in more than 4 seconds after turning the power on. ¶ Press in the Stop mode. 19 The dubbing on Deck A and Deck B ends at different timing. The cassette holder does not open when the area marked "PUSH/OPEN (0)" is pressed. Sound is distorted. ¶ This is due to the difference in tape length or to the characteristics of the cassette deck mechanisms. [. . . ]