User manual KENWOOD KDS-P110
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual KENWOOD KDS-P110. We hope that this KENWOOD KDS-P110 user guide will be useful to you.
Manual abstract: user guide KENWOOD KDS-P110
Detailed instructions for use are in the User's Guide.
[. . . ] · If you experience problems during installation, consult your Kenwood dealer. · When you purchase optional accessories, check with your Kenwood dealer to make sure that they work with your model and in your area. · The RDS feature won't work where the service is not supported by any broadcasting station. · In this document, the description indicator will light means a status is displayed. [. . . ] Select the iPod Equalizer curve Turn the Control knob and push the center when the desired item is displayed. Exit Preset Equalizer mode.
KDS-P110/ KDC-MP642U Adjustment Item Display Range "BAND1" 60/ 100/ 160/ 250/ 400 Hz Band 1 "BAND2" 630/ 1k/ 1. 6k/ 2. 5k Hz Band 2 "BAND3" 4k/ 6. 3k/ 10k/ 16k Hz Band 3 "Q" Quality 0. 25/ 0. 5/ 1. 0/ 2. 0 Band level "GAIN" -9 +9 dB
1 Enter Manual Equalizer Control mode
Select "SOUND" > "Control" > "EQ" > "Manual Equalizer". For how to select Function Control item, refer to <Function Control> (page 6).
2 Select the band you want to set
Turn the Control knob.
3 Select the item you want to set
Push the Control knob towards up or down. Move the cursor ">" to the desired item.
/
· You can select for each source.
4 Set the value
Turn the Control knob.
5 Repeat steps 2 to 4 to complete the Equalizer
curve. To change the band, move the cursor ">" to "band#".
6 Exit Manual Equalizer Control mode
Press the [FNC] button.
/
· When "iPod" is selected in the section <Preset Equalizer curve select> (page 31), Manual Equalizer Control is disabled. · You can select for each source.
English |
31
Sound Setup
Preset position selection
According to the listening position, select the position from the following settings so that the normal position of the sound environment can be compensated in accordance with the selected position; Compensation seat Not compensating. Front-Left seat Front-Right seat Front seat Range "ALL" "Front-Left" "Front-Right" "Front"
Function of KDC-X993/ KDC-X693
Manual position setting
Making fine adjustment of the value specified at Preset position selection per speaker.
1 Enter Manual position setting mode
Select "SOUND" > "Control" > "Position" > "Manual Position". For how to select Function Control item, refer to <Function Control> (page 6).
2 Select the speaker you want to set
Item "FRONT" / "L" "FRONT" / "R" "REAR" / "L" "REAR / "R" "SUBWOOFER" / "L" "SUBWOOFER" / "R" "INITIAL" Setting overview Front Left speaker Front Right speaker Rear Left speaker Rear Right speaker Subwoofer Left Subwoofer Right Initialize the setting values.
1 Enter Preset position setting mode
Select "SOUND" > "Control" > "Position" > "Preset Position". For how to select Function Control item, refer to <Function Control> (page 6).
2 Select the seat you want to compensate
Turn the Control knob.
3 Exit Preset position setting mode
Press the [FNC] button.
Push the Control knob towards up or down.
3 Set the value
Turn the Control knob. Press the Control knob for at least 1 second if you want to execute the "INITIAL".
4 Exit Manual position setting mode
Press the [FNC] button.
32 |
KDC-X993/ KDS-P110/ KDC-X693/ KDC-MP642U
Audio Preset Memory
Registering the value setup by Sound Control.
Audio Preset Recall
Recalling the sound setup registered by <Audio Preset Memory> (page 33).
1 Setup Sound Control
Refer to the following operations to setup the Sound Control. - Cabin selection (page 29) - Speaker Setting (page 29) - DTA (Digital Time Alignment) setting (page 30) - X'Over setting (page 30) - Manual Equalizer Control (page 31) - Preset position selection (page 32) - Manual position setting (page 32)
1 Select the source
Press the [SRC] button.
2 Enter Audio preset recall mode
Select "SOUND" > "Preset" > "Recall". If a PIN code cannot be input from this unit, it can be input from the Bluetooth device. · If there are 5 or more Bluetooth devices registered, you cannot register a new Bluetooth device. · If the error message appears even though the PIN code is correct, try <Registering Special Bluetooth device> (page 36).
When registering from Bluetooth devices
1 Turn on the control unit. 2 Start registering a unit by operating the
Bluetooth device By operating the Bluetooth device, register the hands-free unit (pairing). Select "KENWOOD BT CD/R-2P2"/ "KENWOOD BT200" from the list of connected units.
Registering Special Bluetooth device
Allow registration of a special device that cannot be registered normally (pairing).
3 Enter a PIN code
Input the PIN code registered as mentioned in <Registering PIN Code> (page 36). Check that registration is complete on the Bluetooth device.
1 Select Special device registration mode
Select "MENU" > "SPCL DVC Select". For how to select Function Control item, refer to <Function Control> (page 6).
4 By operating the Bluetooth device, start handsfree connection.
When registering from this unit
2 Enter Special device registration mode
Press the Control knob for at least 1 second. A list is displayed.
1 Select Bluetooth device registration mode
Select "MENU" > "Device Regist". For how to select Function Control item, refer to <Function Control> (page 6).
3 Select a device name
Turn the Control knob and push the center when the desired device name is displayed. If "Completed" is displayed, registration is completed.
2 Enter Bluetooth device registration mode
Press the Control knob for at least 1 second. When search is completed, "Finished" is displayed.
4 Go through the procedure of <Registering
Bluetooth device> (page 36) and complete the registration (pairing).
3 Select the Bluetooth device
Turn the Control knob and push the center when the desired Bluetooth device is displayed.
Cancelling Special device registration mode Press the [FNC] button for at least 1 second.
4 Input the PIN code
Operation type Select the numbers. [. . . ] The preset content may not be recalled depending on the selected source or mode. No call.
USB REMOVE (Blink): The Remove mode has been selected for the USB device/iPod. No Voice: NO Number: No Data: · The calling party does not notify a caller ID. The cell-phone has not been registered (pairing).
HD Memory Full: The tag memory of HD Radio is FULL. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE KENWOOD KDS-P110
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual KENWOOD KDS-P110 will begin.