User manual KENWOOD KGC-4032

[. . . ] · When replacing a fuse, only use a new one with the prescribed rating. Using a fuse with the wrong rating may cause your unit to malfunction. · To prevent short circuits when replacing a fuse, first disconnect the wiring harness. · During installation, do not use any screws except for the ones provided. [. . . ] · During installation, do not use any screws except for the ones provided. The use of improper screws might result in damage to the main unit. NOTE · If you experience problems during installation, consult your Kenwood dealer. · If the unit does not seem to be working right, try pressing the reset button first. If that does not solve the problem, consult your Kenwood dealer. GRAPHIC EQUALIZER KGC-4032 1 2 3 9 PATTERN SPECTRUM ANALYZER S. A SPEANA DEMO 4V PREOUT DISP SUBWOOFER LEVEL ADJUSTABLE MENU 60 120 250 380 500 750 1k 2k 4k 8k 16k Reset button Cleaning the Faceplate Terminals If the terminals on the unit or faceplate get dirty, wipe them with a dry, soft cloth. Cleaning the Unit If the front panel gets dirty, turn off the power and wipe the panel with a dry silicon cloth or soft cloth. 2CAUTION Do not wipe the panel with a stiff cloth or a cloth dampened by volatile solvents such as paint thinner and alcohol. They can scratch the surface of the panel and/or cause the indicator letters to peel off. --3-- Buttons and Display English Release button 2 GRAPHIC EQUALIZER Equalizer operations KBS (Kenwood Built-in Sound) 3 SPEANA DEMO u S. A Four types of loudness levels and equalizer curves for rock, pops, vocal, and flat music genre have been preset. You can call up an equalizer curve for each genre at the touch of a button. Switching between KBS1, KBS2 and USER: KGC-4032 1 2 3 9 PATTERN SPECTRUM ANALYZER S. A 4V PREOUT EQ 1 Press the EQ button. 2 Each time you press the EQ button, the function changes from KBS1 to KBS2 to USER. 3 KBS1 3 KBS2 3 USER When KBS1 or KBS2 or USER is ON, the respective KBS1 or KBS2 or USER indicator lights. Selecting an equalizer curve preset in KBS1 or KBS2 or USER: Press any one of buttons 1 to 3. The selected curve is set and displayed, and the sound quality is changed accordingly. SUBWOOFER LEVEL ADJUSTABLE MENU 60 120 250 380 500 750 1k 2k 4k 8k 16k #1-3 d Title display EQ MENU MENU indicator DEMO indicator KBS indicator USER indicator No. The faceplate will be set and the unit will be operational. NOTE £ English Release button GRAPHIC EQUALIZER KGC-4032 SPE-ANA 1 2 3 9 PATTERN SPECTRUM ANALYZER S. A 4V PREOUT DISP When there is difficulty in setting the faceplate, align the depression on the left side of the faceplate with the shaft of the unit, then lock. Shaft Depression SUBWOOFER LEVEL ADJUSTABLE MENU 60 120 250 380 500 750 1k 2k 4k 8k 16k NOTE · If the controls remain untouched for a period of 5 minutes or more after the panel has dropped open or been removed, the sound output stops automatically. (A warning beep starts sounding 30 seconds before the sound output stops automatically. ) · The faceplate is a precision piece of equipment and can be damaged by shocks or jolts. For that reason, keep the faceplate in its special storage case whilst detached. · Do not expose the faceplate or its storage case to direct sunlight or excessive heat or humidity. Also avoid places with too much dust or the possibility of water splashing. --8-- Accessories External view . . . . . . . . . To prevent a short circuit, remove the key from the ignition and disconnect the - battery. Connect the wiring harness cables in the following order: ground, battery. Press the reset button. 2CAUTION 1 . . . . . . . . . 1 2 . . . . . . . . . 2 3 . . . . . . . . . 1 2CAUTION 4 . . . . . . . . . 2 The use of any accessories except for those provided might result in damage to the unit. Make sure only to use the accessories shipped with the unit, as shown above. · If the fuse blows, first make sure that the cables have not caused a short circuit, then replace the old fuse with one with the same rating. · Do not let unconnected cables or terminals touch metal on the car or anything else conducting electricity. [. . . ] Make sure only to use the accessories shipped with the unit, as shown above. · If the fuse blows, first make sure that the cables have not caused a short circuit, then replace the old fuse with one with the same rating. · Do not let unconnected cables or terminals touch metal on the car or anything else conducting electricity. To prevent short circuits, also do not remove the caps on the ends of the unconnected cables or the terminals. · After the unit is installed, check whether the brake lamps, indicators, wipers, etc. [. . . ]