User manual KENWOOD KR-5200

[. . . ] In order to effectively use the remote control it is important to read the operating instructions and obtain a proper understanding of the remote control and how to switch its operation modes (etc. ). Using the remote control without completely understanding its design and how to switch the operation modes may result in incorrect operations. B60-3609-00 00 CS MA (T, E2, Q) ID 99/12 11 10 9 8 7 6 5 4 3 2 1 98/12 11 10 9 8 7 6 5 4 3 2 Remote Control Other Operations Preparation Getting started 2 Before applying the power Units are designed for operation as follows. AC 230 V only Russia . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AC 220 V only Caution : Read this page carefully to ensure safe operation. KR-5200/V6010/V5010 (En/T) Unpacking Unpack the unit carefully and make sure that all accessories are put aside so they will not be lost. [. . . ] On the KRF-V5010, press the SPEAKERS key to switch the speakers on and off. The indicator for the speakers you want to use should be lit. SP A L R Indication in feet 1)FT 3. )M Indication in meters · The allowable setting range is 1 to 30 feet (0. 3 to 9. 0 m), adjustable in 1 foot (0. 3 m) increments. 4 Repeat steps 2 and 3 to input the distance for the surround speaker. 5 Setup is complete when the input indication reappears. L R SW Display when all speakers have been selected. · If you used the remote control (RC-R0507) to perform the settings, press the VIDEO key at this point to turn off the remote control's own adjustment mode. In this case, the input source is not switched. CD Speaker indicator lights. SP AB L R SW L R SW Models other than KRF-V5010 KRF-V5010 Selecting VIDEO 2/MONITOR Depending on the component connected to the VIDEO 2/MONITOR jacks, select either the "VIDEO 2" setting or the "MONITOR" setting, as appropriate. 8 Normal playback KR-5200/V6010/V5010 (En/T) Listening to a source component VOLUME CONTROL INPUT SELECTOR Adjusting the sound SOURCE DIRECT VOLUME CONTROL BASS BOOST SOUND 15 AUDIO VIDEO PHONES MULTI CONTROL SPEAKERS A/B SPEAKERS, MUTE (KRF-V5010) VIDEO BASS BOOST VOLUME VOLUME VOLUME TUNING/SKIP MUTE SOUND RC-R0307 MUTE VOLUME SOUND MULTI CONTROL RC-R0507 RC-R0307 RC-R0507 1 Use the input selector (INPUT SELECTOR (AUDIO, VIDEO)) to select the source you want to listen to. The input sources change as shown below: Selecting a source using the INPUT SELECTOR knob 1 2 3 4 5 6 7 TUNER "CD" ("CD"*) "TAPE" or "MD" ("TAPE"*) "PHONO"("PHONO"*) "VIDEO1" ("VCR1"*) "VIDEO2" ("VCR2"*) "DVD 6ch" The following adjustments are possible if the receiver is in the stereo mode. (Press the SOUND key once. ) TREB: Select this to adjust the high frequency range. (Press the SOUND key twice. ) SP Selecting a source using the AUDIO key on the remote control (RC-R0507) 1 2 3 4 "CD" ("CD"*) "TAPE" or "MD" ("TAPE"*) TUNER "PHONO"("PHONO"*) A L R SW TREB +4 AUTO MEMO. STEREO ST. TUNED 2 Use the MULTI CONTROL (TUNING/SKIP) to adjust the sound quality. · The bass and treble levels are adjustable from -10 to +10 in 2 step increments. 2 Start playback on the cassette deck connected to the MD/TAPE jacks and start recording on the cassette deck connected to the VIDEO2/MONITOR jacks. · To copy tapes using a double cassette deck, refer to the instruction manual of the double cassette deck. Make sure the SPEAKERS indicators are turned off. A A SW Models other than KRF-V5010 C KRF-V5010 C MONITOR function (analog sources only) You can connect a cassette deck or graphic equalizer to the VIDEO2/ MONITOR jacks of the receiver. If a graphic equalizer is connected, the VIDEO2/MONITOR key should be left in the on position. Alternately, if a cassette deck equipped with a 3-head system is connected to the VIDEO2/MONITOR jacks, you will be able to monitor the just-recorded signal while making recordings on the cassette deck. By switching the VIDEO2/MONITOR key on and off, you can compare the sound of the source signal and the just-recorded signal. For more information, refer to the instruction manual of the connected component. To adjust the input level when the monitor function is turned on, use the SOUND key and the MULTI CONTROL key. ¢ · If you turn off all of the speakers when in the surround mode, the mode is cancelled as well, resulting in stereo playback. 2 Connect headphones to the PHONES jack. PHONES 3 Use the VOLUME CONTROL knob (VOLUME) to adjust the volume. Recording video When recording video, switch the VIDEO2/MONITOR setting to "VIDEO2". 8 1 Use the input selector to select the video source (other than "VIDEO2") you want to record. 3 Start playback, then start recording. To adjust the balance Use the test tone feature. [. . . ] 1 V / 1 k (only KR-5200, KRF-V6010) PRE OUT (SUBWOOFER) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 V / 600 Tone control BASS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±10 dB (at 100 Hz) TREBLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±10 dB (at 10 kHz) Caution : Read this page carefully to ensure safe operation. KR-5200/V6010/V5010 (En/T) VIDEO section VIDEO inputs / outputs VIDEO (composite) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]