User manual KENWOOD RC-R0507

[. . . ] (This step is very important. ) Step 5 POWER Press the POWER key to see if you can turn the component on and off. (If the component you want to control has a mechanical power key that cannot be operated by remote control, press the PLAY key or the TUNING/SKIP key to test it. ) Step 2 ENT Hold down ENT key until the backlight flashes twice (about three seconds). If the component does not respond when you try to control it, return to step 4 and enter the next setup code on the list. Repeat this procedure until you find the code that matches the component. Step 6 ENT For step 2 through step 8, make sure you start the next step within five seconds of completing the previous one. If more than five seconds elapses between any two steps, you will need to go back and start over from step 2. Press the ENT key to store the code. Step 7 Step 3 AUDIO VIDEO TV Repeat steps 3 though 6 to enter the codes for each component you want to control. [. . . ] Otherwise, point the remote control at the component you want to operate. Remote Control Getting the most from your remote control RC-R0507 (En/T) Changing (confirming) the operation mode This operation lets you change the remote control operation mode without changing the input selector. You may find this useful when you want to control one component while using another. (For example, if you want to rewind the tape deck while listening to a CD. ) This operation is also useful if you don't know the which mode the remote control is set to. Executing this operation allows you to change or reconfirm the operation mode you desire. Preparing for automatic operations (MACRO play) The macro play function allows you to set the remote to control several components in succession. After completing this setup, you can perform a series of operations automatically. Enter the setup codes for the components you want to control beforehand. 5 VIDEO, AUDIO, TV SHIFT MACRO VIDEO, AUDIO, TV 1 Make a plan of the macro play you want to Setup. The order of the operations may be fairly complex and you may not be remember all of the necessary commands during the setup procedure. Use the space provided below to write down the operations in the order you are going to enter them. @ # $ % ^ & * ( ) 2 Press the VIDEO, AUDIO or TV key repeatedly to display the remote control mode for the component you want to control. A L R SW The component to be controlled is displayed in parenthesis · Pressing any other keys after the SHIFT key cancels the shift function and sends the normal code associated with the respective key. · If you press VIDEO or AUDIO key more than 3 seconds after pressing the SHIFT key, the input selector changes together with the operation mode. CD 8 9 0 · Up to 20 steps can be memorized for each macro. · At this time all inputs become available regardless of any earlier registration. Press the VIDEO, AUDIO, or TV key repeatedly to select the desired component. · Example 1 : To delete the registration of the component connected to the VIDEO 1 jacks, select "VIDEO 1". · To resume all of the factory settings, proceed step 1, then enter "981". 5 Press the MACRO key so that the backlight flashes twice. · The macro is stored at the locations specified in step 3. If another macro was previously stored at the same location, it is erased. This completes the macro programming procedure. Checking a setup code Executing an automatic operation VIDEO, AUDIO, TV MACRO Perform each step within 5 seconds. Press the VIDEO, AUDIO, or TV key repeatedly to select the desired component. · The backlight flashes twice immediately after the "0" is input to confirm input. This is the first number of the 4 digit setup code. 1 Press the MACRO key. Go to step 2 within 3 seconds. · If the backlight does not blink, the first digit in the setup code is 0. · If the backlight does not blink, the second digit in the setup code is 0. · If the backlight does not blink, the third digit in the setup code is 0. · If the backlight does not blink, the fourth digit in the setup code is 0. 2 Press the VIDEO, AUDIO or TV key to execute the corresponding macro play. · "MACRO" appears in the front panel and the pre-programmed macro is performed: VIDEO = "MACRO 1", AUDIO = "MACRO 2", TV = "MACRO 3" · Some devices take up to 1 second to power on. [. . . ] CALL 1 TV/SAT/VID 2 INFO 3 ALT AUD 1 TV/SAT/VID 2 INFO 3 ALT AUD 4 6 ¢ 4 +100 5 REPEAT 6 RANDOM 4 +100 5 REPEAT 6 RANDOM 7 8 DISPLAY 9 ENT 7 8 DISPLAY 9 Remote Control 7 + (¡ Search) ­ (1 Search) +10 0 0 6 8 7 4 ¢ (3 Play) (Pause) (Stop) (Skip back) (Skip forward) Numeric keys FUNCTION SHIFT commands +100 (+100) REPEAT (Repeat) RANDOM (Random) Remote operation of other components RC-R0507 (En/T) TV operations FUNCTION SHIFT MENU THEME FAV 15 THEME FAV TUNING/SKIP P. CALL 2 INFO 3 ALT AUD MENU 1 TV/SAT/VID 2 INFO 3 ALT AUD TV/SAT/VID 4 4 6 ¢ +100 5 REPEAT 6 RANDOM 4 +100 5 REPEAT 6 RANDOM 7 7 +10 8 DISPLAY 9 ENT 7 8 DISPLAY 9 0 0 + (Channel +) ­ (Channel ­) 6 (Mute) 8 (Volume +) 7 (Volume ­) Numeric keys FUNCTION SHIFT commands TV/SAT. /VID (Input selector) ALT AUDIO (Alternate audio) +100 (TV TEXT) REPEAT (Text off) RANDOM (MIX) VCR operations FUNCTION SHIFT MENU THEME FAV MENU THEME FAV TUNING/SKIP P. CALL 2 INFO 3 ALT AUD 1 TV/SAT/VID 2 INFO 3 ALT AUD REC TV/SAT/VID 4 ¢ +100 5 REPEAT 6 RANDOM 4 +100 5 REPEAT 6 RANDOM 4 6 7 7 +10 8 DISPLAY 9 ENT (¶ Record) GUIDE 7 8 DISPLAY 9 0 0 + (Channel +) ­ (Channel ­) 6 8 7 4 ¢ (3 Play) (Pause) (Stop) (1 Rewind) (¡ Fast forward) Numeric keys FUNCTION SHIFT commands TV/SAT. /VID (Input selector) (OSD menu) LD player operations MENU THEME FAV FUNCTION SHIFT MENU THEME FAV TUNING/SKIP P. CALL 1 TV/SAT/VID 2 INFO 3 ALT AUD 1 TV/SAT/VID 2 INFO 3 ALT AUD 4 ¢ +100 5 REPEAT 6 RANDOM 4 +100 5 REPEAT 6 RANDOM GUIDE 4 6 7 7 +10 8 DISPLAY 9 ENT 7 8 DISPLAY 9 (OSD menu) 0 0 + (A, A/B) ­ (B) 6 8 7 4 ¢ (3 Play) (Pause) (Stop) (Skip back) (Skip forward) Numeric keys FUNCTION SHIFT commands INFO (Frame- time) REPEAT (Repeat) RANDOM (Random) DISPLAY (Display) Satellite tuner operations MENU THEME FAV FUNCTION SHIFT MENU THEME FAV 1 TUNING/SKIP P. [. . . ]