User manual KENWOOD VR-804

[. . . ] AUDIO VIDEO SURROUND RECEIVER VR-804 KRF-V4080D KRF-V5580D INSTRUCTION MANUAL KENWOOD CORPORATION This instruction manual is for some models. Model availability and features (functions) may differ depending on the country and sales area. About the supplied remote control Compared to standard remote controls, the remote control supplied with this model has several operation modes. These modes enable the remote control to control other audio/video components. In order to effectively use the remote control it is important to read the operating instructions and obtain a proper understanding of the remote control and how to switch its operation modes (etc. ). [. . . ] Use the MULTI CONTROL knob or keys to adjust the volume level of the test tone output from the speaker channel to be adjusted. For AUTO selection, the test tone is heard from the speakers in the following sequence for 2 seconds each: · The speakers you have selected should appear on the display. 7 Press the SETUP key to exit the SETUP mode. Input level adjustment (analog sources only) If the input level of an analog source signal is too high, the CLIP indicator will blink to indicate the source signal. Adjust the input level. 1 Use the INPUT SELECTOR knob to select the source of which the input level you want to adjust. 2 Press the SOUND key repeatedly until the "INPUT" indication appears. 3 Use the MULTI CONTROL knob or keys to adjust the input level. · If you change the volume level settings for the speakers while listening to music, the settings referred to on this page are also changed. § · If any of the speaker is set as OFF during SP SETUP, the TEST TONE adjustment for the speaker will be skipped. · The input level may be adjusted to any one of three settings: 0dB, -3dB, and -6dB. (The initial setting is 0dB. ) 4 Press the SOUND key again to return to the input indication. 17 EN Normal playback Preparing for playback Some preparatory steps are needed before starting playback. Listening to a source component VOLUME CONTROL INPUT SELECTOR POWER ON/STANDBY SPEAKERSON/STANDBY (KRF-V4080D/ V5580D) ON/OFF (VR-804) POWER ON/OFF (KRF-V4080D/ V5580D) AUTO INPUT SELECTOR Turning on this model 1 Turn on the power to the related components. 2 Turn on the power to this model by pressing POWER ON/ STANDBY (for VR-804) or POWER ON/OFF and ON/ STANDBY (for KRF-V4080D/V5580D) key. Input Selector VOLUME 1 Use the INPUT SELECTOR knob or keys to select the source Selecting the input mode If you have selected a component connected to the CD/DVD, VIDEO2, DVD (VR-804/KRF-V5580 only) or DVD/6CH (KRF-V4080D only) jacks, make sure that the input mode setting is correct for the type of audio signal to be used. 8 you want to listen to. The input sources change as shown below: 1 2 3 4 5 6 7 "AUX" "TUNER" "CD/DVD" "TAPE" or "MD" "VIDEO1" "VIDEO2" "DVD" or "DVD/6CH" (for KRF-V4080D only) Selecting MD/TAPE Select the source name corresponding to the component connected to the MD/TAPE jacks. To change the source to "MD", follow the steps below: 1 Use the INPUT SELECTOR knob to select "TAPE". · To return to the original indication, repeat procedure 2. 2 Start playback from the selected source. 3 Use the VOLUME CONTROL knob or VOLUME keys to adjust the volume. Setting the speaker status The speaker indicator lights up. Press the SPEAKERS ON/OFF key to switch the speaker on or off. 18 EN Normal playback Adjusting the sound Adjusting the LOUDNESS mode (remote control only) SPEAKERS ON/OFF ACTIVE EQ VOLUME CONTROL You can adjust the Loudness function which controls the low volume settings to maintain the music's richness. The adjustment can be made when this model is in the PCM stereo and analog stereo mode. Press the LOUDNESS key to turn the LOUDNESS setting ON. To cancel Press the LOUDNESS key again so that the "LOUDNESS" indicator goes off. PHONES MULTI CONTROL MUTE Muting the sound The MUTE key lets you mute the sound of the speakers. Press the MUTE key. BASS BOOST MUTE LOUDNESS MULTI CONTROL ACTIVE EQ TONE VOLUME To cancel Press the MUTE key again so that the "MUTE" indicator goes off. · MUTE ON can also be deactivated by turning the volume control knob. Adjusting the TONE (remote control only) You can adjust the sound quality when the model is in the PCM stereo and analog stereo mode. 2 Use the MULTI CONTROL knob or keys to select TONE ON/OFF. ACTIVE EQ mode You can enjoy a more impressive sound effect when ACTIVE EQ is turned ON during Dolby Digital and DTS playback and, when in PCM and analog stereo mode Press the ACTIVE EQ key for the following selections; 1 ACTIVE EQ MUSIC : Effective when listening to music. (The ACTIVE EQ LED indicator lights up. ) 2 ACTIVE EQ CINEMA : Effective when watching a movie. (The ACTIVE EQ LED indicator lights up. ) 3 ACTIVE EQ TV : Effective when watching TV. (The ACTIVE EQ LED indicator lights up. ) 4 ACTIVE EQ OFF : The ACTIVE EQ function is turned OFF. (The ACTIVE EQ LED indicator goes off. ) · ACTIVE EQ function will not be available when REC MODE, AUTO TUNING or PRESET MEMORY is ON and during 96kHz LPCM playback. 3 When in TONE ON selection, press the TONE key for the following displays. [. . . ] 68 dB (71. 2 dBf input) Stereo separation (1 kHz) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 dB Selectivity (±400 kHz) VR-804 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (30 Hz ~ 15kHz), +0. 5 dB, ­3. 0 dB For other countries AUDIO section (KRF-V4080D/V5580D) Rated power output during STEREO operation 100 watts per channel minimum RMS, both channels driven, at 8 from 40 Hz to 20 kHz with no more than 0. 7% total harmonic distortion. (FTC) Effective power output during SURROUND operation FRONT (1 kHz, 0. 7% T. H. D. [. . . ]