User manual KRESS FM 1101

[. . . ] The symbols used in these instructions and, if apEN plicable, on the power tool serve to bring your attention to potential dangers when working with this power tool. You must understand the significance of these symbols/notes and comply with them in order to make its use more efficient and safer. The safety warnings, notes and symbols are not a substitute for regulation measures for accident prevention. Warning of dangerous electrical voltage Warning of hot surfaces -WARNINGFor a potentially dangerous situation which could lead to physical injury or material damage. [. . . ] Therefore, electrical tools must always be operated with the necessary caution. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. While reading the operating instructions, unfold the graphics page for the machine and leave it open. Device components 1 2 3 4 5 6 7 8 Locknut Collet chuck Spindle Locking button On/off switch Speed governor turning wheel Mains cable module Locking for mains cable module Illustrated or described accessories are not necessarily included in the scope of delivery Scope of supply See packaging Milling and grinding motor Input power Watt Output power Watt Idle speed min-1 Speed for rated load min-1 Tool fitting with collet chuck ø mm Grinding tool ø , max. Mm Milling-ø mm Dimension mm Weight kg Protection class Milling and grinding motor Input power Watt Output power Watt Idle speed min-1 Speed for rated load min-1 Tool fitting with collet chuck ø mm Grinding tool ø , max. Mm Milling -ø mm Dimension mm Weight kg Protection class Milling and grinding motor Input power Watt Output power Watt Idle speed: 1050FME min-1 1050FME-1 min-1 Speed for rated load min-1 Tool fitting with collet chuck ø mm Grinding tool ø , max. The fitted milling and grinding motor is designed for milling wood and plastics and for grinding wood, plastic, steel and aluminium. The motor must not be guided by hand without appropriate milling attachments. 18 English Your power tool is doubly insulated in compliance with EN 60745; there is thus no need for an earth wire. EN The machine is radio and TV interference-free in accordance with EN 55014-1 and interferenceproof in accordance with EN 55014-2. Push the two unlocking buttons 4 and remove the mains cable module 7 from the handle. The A-weighted noise level of the device is typically: Sound pressure level (LpA) 78 dB(A) Sound power level (LwA) 89 dB(A) Measurement uncertainty K = 3 dB The noise level can exceed 85 dB(A) during operation. Continuous electronic control (Option) The continuous electronic control keeps the speed almost constant under no-load and under load and ensures uniform performance. Electronic control (Option) In the event of overload or overheating during continuous operation, the speed is automatically reduced until the machine has cooled sufficiently. Soft starter The starting current limitation reduces the starting current. the motor revs up slowly until it reaches the preselected rotational speed. Electronic overload protection With a load that is too high, which therefore implies a risk to the motor, the rotational speed of the milling motor is reduced by the integrated monitoring of the motor. The machine must be released (preferably remove it a short distance from the workpiece) to ensure that you can have full capacity again. Before putting into operation, check that the mains voltage and frequency on the identification plate match the details of your mains supply. If the mains cable is damaged while working, pull the mains plug immediately. Fixed power supply Fixed power supply Damaged mains cables must not be used. English 19 To clamp the tool, you lock the spindle 3 by pressing the locking button 4. [. . . ] If you need to apply the warranty, send the original purchase receipt together with the device to us or to the relevant service centre. The warranty obligations assumed by us shall exclude any further claims on the part of the buyer, in particular the right to cancellation of a sale, reduction and the assertion of damage claims. However, the buyer shall have the right to either a reduction (in the purchase price) or the cancellation of the sales agreement should we fail to eliminate any defects within a reasonable period of time. This does not exclude compensation claims in accordance with §§ 463, 480 Para. [. . . ]