User manual LG LHS-C6230T

[. . . ] Should this happen, unplug or main switch off the unit and contact an authorized service center. Do not insert anything between the air outlet blades because the inner fan may be damaged and could cause injury. Should this happen, switch off the breaker used for your air conditioner and contact your installation specialist. Make sure that the unit is correctly ventilated at all times: Do not place clothing or other materials over it. [. . . ] or Press the on the unit until the indicator lights up Press the button on the remote control. or Press the on the unit until the indicator lights up Each time you press a button, the unit beeps. 4 To set the fan speed to. . . High Med Low Result: 5 E-8 To control the direction of the air flow, refer to page . DB98-22419A-1. indd 8 2007-1-10 20:20:23 Heating Your Room You must select the Heat mode if you wish to heat your room to a specific temperature. You can also set the fan speed. If necessary, press the Result: (On/Off) button. Remote Control Control Panel The operating mode indicator (COOL, FAN or HEAT) on the unit comes on. The air conditioner starts up in the mode selected when the unit was last used. The unit beeps twice. The air conditioner is fitted with a protection mechanism to prevent the unit from being damaged when it is started immediately after being: Plugged in Stopped It will start up aotomatically after about three minutes. If the HEAT indicator is not lit up on the unit: Press the button on the remote control or Press the MODE button on the unit one or more times until the HEAT indicator lights up Result: The unit beeps each time you press MODE. The air conditioner starts up in Heat mode. You can change modes at any time. 3 To adjust the temperature, press the To adjust the temperature, press the or or button on the remote button on the unit one control one or more times until the required temperature is displayed. - The temperature is adjusted by °C and displayed on the control panel - The unit beeps The air conditioner starts cooling if the room temperature is higher than the selected temperature. or Press the on the unit until the indicator lights up Press the button on the remote control. or Press the on the unit until the indicator lights up Press the button on the remote control. or Press the on the unit until the indicator lights up Each time you press a button, the unit beeps. E-9 4 To set the fan speed to. . . High Med Low Result: 5 To control the direction of the air flow, refer to page . DB98-22419A-1. indd 9 2007-1-10 20:20:25 Airing Your Room If the atmosphere in your room is stale, you can air it using the Fan feature and if necessary, evacuate the stale air outside. If you wish to evacuate stale air outside, push the ventilation lever on the front of the unit to the right and the open position ( ). The heat pump inside the air conditioner absorbs heat from outside air and brings it indoors. If the temperature of the outside air drops, the air conditioner will heat less. If you find that the room is not warm enough, use an additional heating appliance. The air conditioner circulates warm air to heat your room;as a result, some time will be required after starting the air conditioner to warm the entire room. If necessarty, set the air conditioner going a short time before you wish to use the room. When outside temperatures are low and humidity is high, frost may form in the unit's condensor when heating with your air conditioner. If this happens: The unit stops heating The air flow blades stop swinging The Deice mode is triggered automatically for about five minutes The DEICE indicator on the unit lights up red No intervention is required from you;after about five minutes, the air conditioner starts operating again normally. High indoor and outdoor temperatures If both the indoor and outdoor temperature are high and you select the Heat mode , the fan and compressor in the unit may stop at times. This is normal;simply wait until the air conditioner switches on again. Heating performances Warm air circulation Frost E-5 DB98-22419A-1. indd 15 2007-2-14 15:11:12 Temperature and Humidity Ranges The following table indicates the temperature and humidity ranges within which the air conditioner can be used . Mode Cooling Heating IndoorTemperature °C to 3°C approx. The automatic protection feature may be triggered and the air conditioner stopped. A water leakage or some other malfunction may happen if the heat exchanger freezes. [. . . ] Installation Conditions As the unit is heavy, the wall or window of the installation area should have sufficient strength and durability for operation of the air conditioner, and for prevention of any vibration or noise. It is advisable to install the air conditioner in the north or west side to prevent the effect of direct sunlight. When installing it in the south or east side due to unavoidable circumstances, it is advisable to install the sunshade to prevent the direct sunlight. In this case, take care not to cause any hindrance to the flow of outside air. [. . . ]