User manual LG PQNFB16A0

[. . . ] The seriousness is classified by the following indications. WARNING CAUTION This symbol indicates the possibility of death or serious injury. This symbol indicates the possibility of injury or damage. s Meanings of symbols used in this manual are as shown below. Be sure not to do. [. . . ] · It can cause fire and electric shock. Hold the plug by the head of the power plug when taking it out. · It may cause electric shock and damage. Do not place heavy goods on product. · It can cause product breakdown. BNU-LW BNU-LW That increase in case of product was been flood certainly in the service center or establishment specialty store commit . · I am responsible for fire and electric shock. Protect the product from handling by a children. Do not apply shock to product. · It can cause accident and product breakdown. BNU-LW · I am responsible for breakdown in case of shock to product. BNU-LW BNU-LW Installation Manual 5 Safety Precautions CAUTION s During usage Clean by soft hands using a cleaning material like a soft cloth. · Otherwise, there can be breakdown and damage to the product. BNU-LW Do not place any live part on the surface having water. · It can cause product breakdown. BNU-LW BNU-LW x Wa Thinner Use recommended Adapter. Avoid contact to the metallic goods such as necklace, coin, key, a watch which may touch the battery even for a short-time. · It may cause product breakdown and injury. Hold the plug by the head of the power plug when taking it out. · Otherwise it can result in product breakdown BNU-LW · It may cause electric shock and damage. BNU-LW 6 Lonworks Gateway BNU-LW Configuration BNU-LW Configuration BNU-LW Accessory Parts BNU-LW BNU-LW Front view Power Supply External S. M. P. S Power : 100~250 VAC 50/60 Hz Input Installation Manual 7 BNU-LW Configuration Name of each part BNU-LW 1 2 3 4 5 6 7 8 1 BUS_A: RS485 Communications cable A (+) 7 GND: Connect when not using the DC 12V power adapter 2 BUS_B: RS485 Communications cable B (-) 8 WINK: It flashes 5 times when receiving the WINK command from the LonWorks system. (Green) Service: It will stay off for normal status and flash when it is not connected to the LonWorks system (Red) It will be turned on when you press the service switch. Service switch: When you press the switch, the Neuron ID will be transmitted to the LonWorks system and the service LED will be turned on. 3 T1, T2: For reserve(not use) 4 LON: TP/FT-10 Communications wire (no polarity) - LonWorks system communications wire 5 PWR: Connect to DC 12V power adapter 6 12V: Connect when not using the DC 12V power adapter WARNING Both 5 and 6/7 are for power supply and only one of the two needs to be connected. When connecting 6/7, do not use 5. 8 Lonworks Gateway System Structure System Structure LonWorks Gateway can be connected to maximum of 64 indoor units. LonWorks-compatible BMS LonWorks* Network Max. 64 indoor & 8 outdoor ON KSDO4H L1 2 3 4 L1 2 3 4 LonWorks* Gateway PI485 RS485 PI485 BNU-LW(LonWorks Gateway) cannot be connected to I-gateway (CNU), PC central controller, Deluxe central controller and simple central controller at the same time. ON KSDO4H Installation Manual 9 Address of the indoor unit connected to the BNU-LW(LonWorks Gateway) Address of the indoor unit connected to the BNU-LW(LonWorks Gateway) LonWorks-compatible BMS system (Indoor units: Maximum of 64 units) A/C No. address A/C No. ON KSDO4H L1 2 3 4 ON KSDO4H L1 2 3 4 1 (0. 0) 17 (1. 0) 33 (2. 0) 49 (3. 0) 2 (0. 1) 28 (1. 1) 34 (2. 1) 50 (3. 1) 3 (0. F) 32 (1. F) 48 (2. F) 64 (3. F) address ON KSDO4H PI485 L1 2 3 4 address A/C No. [. . . ] Check whether the Service LED turns to normal status (off) within 10 minutes. If the Service LED turns to normal status, it the installation has been completely normally. [. . . ]