User manual LG W2294T-PF

[. . . ] To Prevent Fire or Hazards: Always turn the display OFF if you leave the room for more than a short period of time. Keep children from dropping or pushing objects into the display's cabinet openings. When the display is to be left unattended for an extended period of time, unplug it from the wall outlet. In the presence of thunder and lightning, never touch the power cord and signal cable because it can be very dangerous. [. . . ] When you encounter problems such as blurry screen, blurred letters, screen flicker or tilted screen while using the device or after changing screen resolution, press the AUTO/SET function button to improve resolution. 5 Connecting the Display To attach or separate the back door 1. To attach the back door, match the two holes and push the back door as shown in the image. back door NOTE - Cover the back cap after connecting the cables before use. To separate the back door, hold the bottom part and pull it out. Kensington Security Slot Connected to a locking cable that can be purchased separately at most computer stores 6 Control Panel Functions Front Panel Controls Side Button Use this button to enter EZ ZOOMING, 4:3 IN WIDE, PHOTO EFFECT items. For more information, refer to page 11. MENU Button Use this button to enter or exit from the On Screen Display. OSD LOCKED/UNLOCKED This function allows you to lock the current control settings, so that these settings are not inadvertently changed. To lock the OSD settings, press and hold the MENU button for several seconds. You can unlock the OSD settings at any time by pushing the MENU button for several seconds. The message "OSD UNLOCKED" appears. 7 Control Panel Functions -+ Buttons Use these buttons to select or adjust functions in the On Screen Display. For more information, refer to page 16. (SOURCE Hot key) Use this button to make either D-Sub or DVI connector active. The default setting is D-Sub. AUTO/SET Button Use this button to enter a selection in the On Screen Display. AUTO IMAGE ADJUSTMENT When adjusting your display settings, always press the AUTO/SET button before entering the On Screen Display(OSD). This will automatically adjust your display image to the ideal settings for the current screen resolution size (display mode). The best display mode is 1680 x 1050 Power Button/ Power Indicator Use this button to turn the display on or off. The power indicator stays blue if the display is running properly (On mode). If the display is in power saving mode, the power indicator is flickering blue. 8 On Screen Display (OSD) Control Adjustment Screen Adjustment Making adjustments to the image size, position and operating parameters of the display is quick and easy with the On Screen Display Control system. A short example is given below to familiarize you with the use of the controls. The following section is an outline of the available adjustments and selections you can make using the OSD. NOTE Allow the display to stabilize for at least 30 minutes before making image adjustments. To make adjustments in the On Screen Display, follow these steps: -+ + -+ Press the MENU Button, then the main menu of the OSD appears. When the icon you want becomes highlighted, press the AUTO/SET Button. Press the MENU Button once to return to the main menu to select another function. Press the MENU Button twice to exit from the OSD. -+ 9 On Screen Display(OSD) Selection and Adjustment The following table indicates all the On Screen Display control, adjustment, and setting menus. Main menu EZ ZOOMING 4:3 IN WIDE NORMAL Sub-menu A D Reference To adjust the resolution To adjust the image size PHOTO EFFECT GAUSSIAN BLUR SEPIA MONOCHROME BRIGHTNESS To adjust the screen color mode PICTURE CONTRAST GAMMA sRGB PRESET 6500K 9300K To adjust the brightness, contrast and gamma of the screen COLOR RED GREEN BLUE HORIZONTAL VERTICAL To customize the color of the screen To adjust the position of the screen To improve the clarity and stability of the screen TRACKING CLOCK PHASE SHARPNESS LANGUAGE HORIZONTAL OSD POSITION VERTICAL SETUP WHITE BALANCE RTC POWER INDICATOR FACTORY RESET MOVIE INTERNET USER NORMAL DEMO To customize the screen status for a user's operating environment FLATRON F-ENGINE To select or customize desired image settings : Adjustable A : Analog Input D : Digital Input NOTE The order of icons may differ depending on the model (10~16). OSD (On Screen Display) menu languages on the monitor may differ from the manual. 10 On Screen Display(OSD) Selection and Adjustment Pressing the button on the right side of the monitor will display the OSD screen. MENU : Exit - , + : Move SET : Select Main menu EZ ZOOMING Description To select the display resolution. Set your own blue color levels. RED GREEN MENU : Exit BLUE - : Decrease + : Increase SET : Select another sub-menu 13 On Screen Display(OSD) Selection and Adjustment Main menu Sub menu Description TRACKING HORIZONTAL To move image left and right. VERTICAL CLOCK To move image up and down. To minimize any vertical bars or stripes visible on the screen background. The horizontal screen size will also change. PHASE To adjust the focus of the display. [. . . ] · Check if the signal cable is properly connected and use a screwdriver to fasten if necessary. · Set the color setting higher than 24 bits (true color) at Control Panel - Settings. G The screen blinks. · Check if the screen is set to interlace mode and if yes, change it to the recommend resolution. Have you installed the display driver? G Have you installed the display driver?· Be sure to install the display driver from the display driver CD (or diskette) that comes with your display. Or, you can also download the driver from our web site: http://www. lge. com. [. . . ]