User manual LIEBHERR UIK 1550 PREMIUM

[. . . ] Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Food refrigeration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SuperCool. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] u Detach the connecting cable from the rear of the appliance, removing the cable holder at the same time because otherwise there will be vibratory noise!After installation: u Remove the protective film from the decorative trims. u Remove all transit supports. NOTICE Risk of damage due to condensate!u If refrigerator and freezer are installed side-by-side, the freezer always has to be sited to the right of the refrigerator (as seen from the front). Condensate is prevented from forming between the appliances by the foamed-in side wall heating on the left side of the freezer. 3 4 Putting into operation Recess height A 820 mm 820 mm 870 mm 870 mm Height of unit plinth B 100 mm 170 mm 150 mm 220 mm Height of unit door C 716 mm 646 mm 716 mm 646 mm Base height of unit plinth D 100 mm 100 mm 150 mm 150 mm Note u Before assembling the door of the unit, make sure that the admissable weight of the unit door is not exceeded. u Otherwise damage to the telescopic rails and resultant malfunction cannot be ruled out. weight of unit door 10 kg 4. 3. 1 Installing the appliance u Detach the connecting cable from the rear of the appliance, removing the cable holder at the same time because otherwise there will be vibratory noise!u Lay the connecting cable with the help of a string in such a way that the appliance can be easily connected after fitting. Fig. 5 Built-under variants: Slide in and align the appliance: NOTICE Risk of harm to flooring susceptible to damage!6 for recess height 820 or 870 mm A = Height of recess B = Height of unit plinth C = Height of unit door D = Base height of cut-away unit plinth u Pull the plinth panel forwards to remove it. u After having adjusted the inclination, re-tighten all the screws Fig. 22 4. 4. 1 Adjusting the door inclination 4. 4. 2 Aligning the position of the door Note u Always make the adjustment on both sides, left and right! Fig. 21 (32). 8 Control 4. 6 Connecting the appliance NOTICE Risk of damage to the electronic control system!to a. c. / three-phase) or energy saving plugs. WARNING Fire and overheating hazard!The type of current (alternating current) and voltage at the installation site have to conform with the data on the type plate (see Appliance at a glance). Connect the appliance only with a properly installed socket outlet with earthing contact. u Plug in the power plug. 4. 7 Switching on the appliance u Press On/Off button Fig. The temperature display indicates the set temperature. u w u u u u u u u u Vertical adjustment, Y: Unscrew and remove the screws Fig. 23 5 Control 5. 1 Food refrigeration Note u The maximum weight you can store in the pull-out compartment with bottle rack and vegetable bin is 20 kg. u Store readily perishable food such as pre-cooked meals, meat and sausage products in the middle area of the coldest zone. (see Appliance at a glance) u Use recyclable plastic, metal, aluminium and glass containers and cling film for wrapping. [. . . ] 28 First check whether you can correct the fault yourself by reference to the list (see Malfunction). If this is not the case, please contact the customer service whose address is given in the enclosed customer service list. WARNING Risk of injury if repair work is not carried out professionally!u Have any repairs and action - not expressly specified - on the appliance and mains cable carried out by service personnel only. 30 (3) off the type plate located inside the appliance on the lefthand side. Fig. [. . . ]