User manual LIEBHERR WK 4127

[. . . ] · In the event that the appliance is damaged on delivery, contact the supplier immediately before connecting to the mains. · To guarantee safe operation, ensure that the appliance is set up and connected as described in these operating instructions. · When disconnecting the appliance, pull on the plug, not on the cable. · Any repairs and work on the appliance should only be carried out by the customer service department, as unauthorised work could prove highly dangerous for the user. [. . . ] Do not operate the appliance outdoors or in areas where it is exposed to splash water or damp conditions. Setting up GB · Avoid positioning the appliance in direct sunlight or near cookers, radiators and similar sources of heat. · The floor on which the appliance stands should be horizontal and level. Compensate for uneven floors with the adjustable feet. · Always ensure that there is good ventilation and that the outward flowing air is able to escape. · Standard EN 378 specifies that the room in which you install your appliance must have a volume of 1 m3 per 8 g of R 600a refrigerant used in the appliance, so as to avoid the formation of inflammable gas/air mixtures in the room where the appliance is located in the event of a leak in the refrigerant circuit. The quantity of refrigerant used in your appliance is indicated on the type plate on the inside of the appliance. · Do not connect the appliance to the supply with other equipment using an extension cable - risk of overheating. Dimensions WK 2926 - A=1250 mm WK 2927 - A=1264 mm WK 4126 - A=1644 mm WK 4127 - A=1658 mm Connecting to the mains Power supply (a. c. ) and voltage at the operating point must comply with the details on the type plate. The socket must be fused with a 10 A fuse or higher, it must be away from the rear of the appliance and must be easily accessible. Connect the appliance with a properly earthed fused plug and socket only. - Always ensure good ventilation. - Do not place appliance in areas of direct sunlight or next to a stove, heater or similar object. - Keep the time the appliance is open to a minimum. Saving energy Accumulated dust increases the energy consumption: - Once a year, dust the refrigerating unit together with the metal grille of the heat exchanger at the back of the appliance. 9 Switching the appliance on and off To switch the appliance on: Connect the appliance to the mains - the appliance is switched on. To switch the appliance off: Pull out the mains plug or set the temperature control to 0. You are recommended to clean the appliance before switching it on for the first time (see Cleaning). Air exchange with activated charcoal filter The way in which wines continue to mature depends on the ambient conditions. The quality of the air is therefore decisive for preserving the wine. Setting the temperature We recommend that you replace the filter once a year. Inserting the filter: Insert with the handle in a vertical position. Turn it 90° to the left or right until it clicks into place. Using a coin, turn the arrow on the temperature control to a setting between 0 und max. The nearer the temperature control is to the max. setting, the colder the interior temperature. If you are storing wine for long periods of time, it should be stored at a temperature of between 10°C and 14°C. Storing wine This is the temperature wine cellars are kept at, and it is just right to allow wine to mature properly. The following drinking temperatures are recommended for the various types of wine. Red wines: +14°C to +18°C Rosé wines: +10°C to +12°C White wines: +8°C to +12°C Sparkling wines, Prosecco +7°C to +9°C Champagne +5°C to +7°C The interior light is fitted on the inside at the top. It can be switched on and off by pressing the switch S. Interior light in appliances with glass door Labels The appliance is supplied with a label holder with labels for each shelf. Fitting: Click the label holder into place and slide the label in from the side. · Unscrew the cover panel. [. . . ] ­ Does the appliance cause nearby items of furniture or objects to vibrate?Ensure that the appliance is stable and that all parts at the back can vibrate freely. Please note that noises caused by the refrigerant circuit cannot be avoided. · The temperature is not low enough: ­ Is the temperature setting correct (see , , Setting the temperature")?­ Does the separately installed thermometer show the correct reading? [. . . ]