User manual LIEBHERR ZKES 453

[. . . ] 21 Operating and control elements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Switching on for the first time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Setting the temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Adjusting the humidity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] - The electronic controls will switch over automatically about 5 seconds after the last time you pressed the button, and the interior temperature will be displayed. The temperature can be set between +16°C and +20°C. 22 Adjusting the humidity To reduce the humidity: Press the Down button. To increase the humidity: Press the Up button. GB - While you are setting the humidity, the display will flash. - About 5 seconds after the button was last pressed, the actual interior humidity will be displayed. The humidity can be adjusted between 68% and 75%. Lighting The light is integrated into the door frame and can be switched on and off by pressing the Light button. · Press and hold the Light button and at the same time press the humidity setting buttons to increase or decrease the brightness. Down = darker, Up = brighter. 23 Audible warning signal The audible warning signal sounds in the event of a malfunction. It will always sound when the door has been left open for longer than 60 seconds. It will also sound if the interior becomes too cold or too warm or if the humidity is too high or too low. LED will light up. Control elements LED lights up when the lighting is operational. LED flashes when the temperature or humidity inside the appliance is too high or too low. This alarm will activate when the water level drops to 400 ml (sufficient to allow the appliance to run properly for another 6 weeks). When topping up the water, always remove any impurities such as cigar leaves. If the water tank is very dirty, clean it and refill with fresh water. 24 Setup mode The following functions can be activated in setup mode: = Child lock = Display brightness GB = Child lock The child lock is designed to protect the appliance from being switched off accidentally. Activating the child lock · Activate setup mode by pressing the - The display reads · Press the button. button for 5 seconds. - The display reads · Press the - The button again. symbol will light up to indicate that the child lock is activated. button. · Exit setup mode by pressing the Deactivating the child lock · Activate setup mode by pressing th - The display reads · Press the button. button for 5 seconds. - The display reads · Press the - The button again. symbol will go out, indicating that the child lock is deactivated. button. · Exit setup mode by pressing the 25 = Display brightness Adjusting the display brightness · Activate setup mode by pressing the · Press the Press the button until button. button for 5 seconds. appears in the display. - The display reads · Press the buttons and set the brightness between 0 = minimum and 5 = maximum. · When you reach the desired level, press the · Exit setup mode by pressing the button. The new setting will activate after about 1 minute. 26 Equipment Air exchange with activated charcoal filter To guarantee optimum air throughput, the appliance is fitted with an activated charcoal filter at the top of the rear wall. Changing the filter: The filter can be removed by depressing the recesses on the left and right with a small screwdriver. Spanish cedarwood shelves The presentation boxes are designed for storing cigars individually. [. . . ] · Disable discarded appliances by removing the plug and cutting through the connection cable. Render the catch unusable so that children cannot become trapped inside. · Ensure that the refrigerant circuit is not damaged when the appliance that is no longer needed is taken away for disposal. · Details of the refrigerant used can be found on the type plate. [. . . ]