User manual MOTOROLA DCT6208

[. . . ] User Guide DCT6200/DCT6208 High Definition Cable Receiver CAUTION RISK OF ELECTRIC SHOCK CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. Graphical symbols and supplemental warning marking locations on bottom of terminal. WARNING TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION TO PREVENT ELECTRICAL SHOCK, DO NOT USE THIS (POLARIZED) PLUG WITH AN EXTENSION CORD, RECEPTACLE, OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point, within an equilateral triangle, is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. REPAIRS If you find the unit in need of repair, call Motorola Support at 1-866-668-2271 or 1-866-MOT-BCS1. NOTE TO CATV SYSTEM INSTALLER This reminder is provided to call the CATV system installer's attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close as possible to the point of cable entry as practical. EXAMPLE OF ANTENNA GROUNDING bäÉÅíêáÅ=ëÉêîáÅÉ dêçìåÇ ÉèìáéãÉåí Åä~ãé ^åíÉåå~=äÉ~Ç= áå=ïáêÉ ^åíÉåå~ ÇáëÅÜ~êÖÉ=ìåáí= Ekb`=pÉÅíáçå=UNMJOMF dêçìåÇáåÖ Åä~ãéë dêçìåÇáåÖ=ÅçåÇìÅíçêë Ekb`=pÉÅíáçå=UNMJONF mçïÉê=ëÉêîáÅÉ=ÖêçìåÇáåÖ ÉäÉÅíêçÇÉ=ëóëíÉã Ekb`=^êíáÅäÉ=ORMI=m~êí=eF kb`Zk^qflk^i=bib`qof`^i=`lab IMPORTANT SAFETY INSTRUCTIONS 1 2 3 4 5 6 7 8 Read instructions All the safety and operating instructions should be read before the appliance is operated. [. . . ] Refer to the interactive program guide instruction manual for detailed instructions. 6 DCT6200/DCT6208 User Guide AUDIO/VIDEO CONNECTIONS Before you move or change components on your entertainment system, review the following: · For basic cable connections, use 75-ohm coaxial cables equipped with F-type connectors. A 6-foot coaxial cable is provided to connect the DCT* to your cable wall outlet. A 6-foot component video cable and left/right audio cables are also provided to connect the DCT* to your TV. If your equipment supports it, S-video connections may be used in place of the standard RCA video connections. In most cases, S-video offers a higher level of standard definition video quality than RCA video If your equipment supports it, the optical (OPTICAL SPDIF) or coaxial digital (SPDIF) audio outputs may be used in place of the stereo audio outputs (AUDIO R and L). In most cases these outputs offer a higher level of audio quality, including support for 5. 1 Surround Sound. If you are connecting a coaxial cable from the TO TV/VCR connector on the DCT* to the coaxial CABLE/ANTENNA IN connector on the TV, you must tune your TV to channel 3 or 4 to view the DCT* output. Connecting the DCT* in this manner will remove its high definition video capability. Disconnect power from the DCT* before connecting or changing cable connections. · · · · The DCT* offers Component and DVI video outputs. If your High Definition television (HDTV) or home theater receiver supports either of these connections, use one or the other instead of the RCA type or S-Video connections. For more information on connecting High Definition video, see "Connecting your DCT* to an HDTV ­ Video Only" on page 16. CAUTION!Do not place anything on top of the DCT*, especially other home entertainment components. Be sure to provide adequate ventilation to prevent overheating. 7 RF BYPASS oc=ETR=çÜãF ÅçååÉÅíáçå a`qSOMMLa`qSOMU TO TV/VCR ETHERNET RPT OUT IR RF IN RF IN USB TV Pass Card DVI-D OUT AUDIO OUT R AUDIO IN L SPDIF VIDEO IN OUT S-VIDEO Y Pb Pr OPTICAL SPDIF IEEE 1394 CONV OUT RF OUT CABLE IN CONV IN TO TV/VCR CABLE IN From cable outlet To TV 8 DCT6200/DCT6208 User Guide The DCT* may be equipped with an optional RF Bypass switch. When the optional RF bypass switch is activated, it routes the cable signal directly to a cable-ready TV, bypassing the DCT*. This configuration enables you to view clear (unscrambled) analog programming on the direct cable signal should the DCT* be powered off. The RF bypass is not available on all cable systems. 9 OPTIMIZING YOUR DCT* OUTPUT SETTINGS The Motorola DCT* delivers high-quality video for high definition TVs using the YPbPr (component) and DVI-D video connectors. This section describes how to use the on-screen display to set your DCT* to automatically optimize both standard and high definition video based on your HDTV and personal preferences. You can use your on-screen menu to configure your high definition settings for TV type, DVI and/or YPbPr video output and closed captioning. To access your high definition settings, ensure that your DCT* is plugged into a power outlet and is turned off. If your TV is on, the on-screen display menu appears listing the settings you can configure. DVI/YPbPr OUTPUT Use your remote control or the cursor keys on the front panel to navigate the on-screen display. The high definition settings are described in the table on the following pages. 10 DCT6200/DCT6208 User Guide The DVI/YPbPr OUTPUT setting displays as YPbPr OUTPUT if you are not using the DVI video connection. The user settings will also be displayed on the front panel LED whether your TV is off or on. [. . . ] Not all HDTVs can display every output format (1080i, 720p, 480p, or 480i) available on the DCT*. Enter the User Settings menu and cycle through the available output formats until a picture displays on the TV. Verify that all video cables between the DCT* and the TV are firmly connected. There are no graphics, closed captions, or program guides appearing on the TV screen The DCT* cannot generate graphics on all video outputs at all times. If the DCT* is set to 1080i, 720p, or 480p output format, graphics are only available on the high definition video outputs (DVI and component video). [. . . ]