User manual MOTOROLA DCT6412

[. . . ] CAUTION RISK OF ELECTRIC SHOCK CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. Graphical symbols and supplemental warning marking locations on bottom of terminal. WARNING TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION TO PREVENT ELECTRICAL SHOCK, DO NOT USE THIS (POLARIZED) PLUG WITH AN EXTENSION CORD, RECEPTACLE, OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point, within an equilateral triangle, is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. REPAIRS If you find the unit in need of repair, call Motorola Support at 1-866-668-2271 or 1-866-MOT-BCS1. NOTE TO CATV SYSTEM INSTALLER This reminder is provided to call the CATV system installer's attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close as possible to the point of cable entry as practical. EXAMPLE OF ANTENNA GROUNDING Electric service Ground equipment clamp Antenna lead in wire Antenna discharge unit (NEC Section 810-20) Grounding clamps Grounding conductors (NEC Section 810-21) Power service grounding electrode system (NEC Article 250, Part H) NEC=NATIONAL ELECTRICAL CODE IMPORTANT SAFETY INSTRUCTIONS 1 2 3 4 5 Read instructions All the safety and operating instructions should be read before the appliance is operated. [. . . ] (Dependent upon program guide support. ) Simultaneous Watch and Record Record one program in the background while viewing another live broadcast at the same time. 7 Simultaneously Record Two Shows Record two programs from two different channels at the same time. Simultaneously Record Two Shows and Watch a Recorded Program Watch a program recorded on your DCT* while recording up to two other programs at the same time. You can also easily switch viewing the pre-recorded program and either of the programs you're recording. 8 DCT6400 Series User Guide OPTIMIZING YOUR DCT* FOR HIGH DEFINITION TV The DCT* enables you to view HD programming. HDTV provides up to twice the color resolution and up to six times the sharpness of standard definition TV. The Motorola DCT* delivers high-quality video for HDTVs using the YPbPr (component), DVI-D, and IEEE 1394 connectors. This section describes how to use the on-screen display to set your DCT* to automatically optimize both standard and HD video based on your HDTV and personal preferences. If you use the IEEE 1394 connector, no adjustments to your settings are required. If you have a TV with a DVI connection, be sure that the TV is on and connected to the DVI-D OUT connector of the DCT* before adjusting the settings. You can use your on-screen menu to configure your HD settings for TV type, DVI and/or YPbPr video output, and closed captioning. To access your HD settings: 1 Ensure that your DCT* is plugged into a power outlet and is turned off. 9 2 Press the MENU key on the front panel. If your TV is on, the on-screen display menu appears listing the settings you can configure. DVI/YPbPr OUTPUT RESTORE DEFAULTS Use your remote control or the cursor keys on the front panel to navigate the on-screen display: · · · Press the and keys to highlight the setting you wish to change. To exit the menu and save your settings, press the POWER or MENU key. The HD settings are described in the table on the following pages. The DVI/YPbPr OUTPUT setting is displayed as YPbPr OUTPUT if you are not using the DVI video connection. The user settings will also be displayed on the front panel display whether your TV is off or on. If the on-screen display menu does not appear on your HDTV screen, your TV may not support the default video output setting. Use the DCT* front panel display to view and change your settings. 10 DCT6400 Series User Guide User Settings Setting TV Type Description Sets the aspect ratio. Options are 16:9 for wide screen TVs or 4:3 LETTERBOX or 4:3 PAN/SCAN for standard TVs: · · 4:3 LETTERBOX fits widescreen programming on the screen by placing black bars at the top and bottom. 4:3 PAN/SCAN fills the screen by cropping the left and right edges of widescreen programming. DVI/YPbPr Output Sets the video display format for the component video outputs. If you are not using an HDTV with the DCT*, selecting a format other than 480i causes the on-screen display to go blank. If this occurs, you can view the settings on the front panel display to change the YPbPr Output back to 480i. If you are not using the DVI video connection, the DVI/YPbPr OUTPUT setting displays as YPbPr OUTPUT. 11 Setting 4:3 Override Description Sets the display format for 4:3 standard-definition programming. If the YPrPb Output is set to 1080i, 720p, or 480p, this setting defaults to 480i. [. . . ] If the DCT* is set to 480i, graphics are available on all video outputs. If the DCT* is connected to a standard definition TV, verify that the DCT* is configured to use the 480i output mode. Verify that closed captions on the DCT* have been enabled in the User Settings menu. If you are using an IEEE 1394 connection, on-screen graphics, including closed captions and program guides, will not be displayed. There are black bars to the right and left of the picture Wide screen TVs display 4:3 programs in this format unless set to Stretch. [. . . ]