User manual MOTOROLA DRC450

[. . . ] On the DRC450, press and hold TV (at least 6 seconds) until you see the programming mode start. Each of the mode key lights will turn off and on sequentially, starting with AUDIO on through TV, and the sequence will repeat twice. During this time, release TV and wait until it's lit continuously. Press the (Up) cursor key once to start the search mode. NOTE: In the search mode, the DRC450 will send IR codes from its library to the selected component, starting with the most popular codes first. [. . . ] At this time, release the mode key and wait until it's lit continuously. Locate the code for your device in Manufacturer's Codes on the back of this user guide. Brands are listed in alphabetical order with the most popular codes listed first. If you perform this procedure correctly, the selected mode key will blink three times. NOTE: If you enter an invalid code, the selected mode key will turn off. Repeat steps 2 through 4 with a valid code. 2. On the DRC450, press and hold a VCR/DVD for at least 6 seconds, until you see the programming mode start. Each mode key light will turn off and on sequentially, starting with AUDIO on through TV, and the sequence will repeat twice. At this time, release VCR/DVD and wait until it's lit continuously. Locate the code for your device in Setup Codes For TV/VCR Combos on the back. Brands are listed in alphabetical order with the most popular codes listed first. If you perform this procedure correctly, VCR/DVD will blink three times. NOTE: If you enter an invalid code, VCR/DVD will turn off. Repeat steps 2 through 4 with a valid code. 3. To Unlock Volume Lock: 1. On the DRC450, press and hold a mode key (at least 6 seconds) until you see the programming mode start. Each mode key light will turn off and on sequentially, starting with AUDIO on through TV, and the sequence will repeat twice. During this time, release the mode key and wait until it's lit continuously. The mode key light will blink three times, indicating volume has been unlocked for the selected mode. Now, whenever you press VOLUME +, VOLUME -, or MUTE on the DRC450, the volume controls will reset to their original device. 6. 3. 4. USER GUIDE Fold Press POWER once. The TV key will light on and off, showing that an IR code has been sent. If your television does not turn off, press the (Up) cursor key once again to call up the next IR code and press POWER once again. If your television still does not turn off, repeat step 5 as many times as needed until your TV turns off. Press OK once to save the code and the TV key will blink three times, confirming the selection. To search for the codes of your other devices, repeat steps 1 through 7, but substitute the appropriate mode key (i. e. , VCR/DVD, CABLE, or AUDIO) for the device you are searching for. 5. 2. 3. Fold OVERVIEW The Motorola DRC450 universal remote will control up to four devices, including Motorola's interactive digital terminals*, most TVs, VCRs, Amplifiers, DVD players, PVRs, Tuners, and CD players. *NOTE: Digital models include the DCT1000, DCT1200, DCT1700, DCT2000, DCT2500, and DCT5100. [. . . ] Device Type:______________ VCR/DVD Code: CHECKING THE CODES If you have set up the DRC450 using the Searching For Your Code procedure, you may need to find out which four-digit code is operating your equipment. Perform the following procedure after you have set up your devices to find out which four-digit code is operating your equipment. Turn on your TV. FEATURES AND FUNCTIONS Use the DRC450 mode keys (i. e. , AUDIO, VCR/DVD, CABLE, or TV) to control a specific device. When pressed, the selected mode key will light, confirming your choice. Use the other keys to perform desired actions (see the following key chart). NOTE: The selected mode will remain active until you press another mode key. NOTE: When a selected mode key blinks two times with each key press, this indicates that the batteries are getting low. [. . . ]