User manual MOTOROLA DSR470

[. . . ] DSR470 Digital Receiver User Guide This user guide is for use with DSR470 Digital Receivers Publication #479169-001 Rev A All Rights Reserved General Instrument Corporation doing business as Broadband Communications Sector of Motorola, Inc. San Diego, California 92121 Internet: http//www. mot. com This device incorporates an anticopy process technology that is protected by U. S. Reverse engineering or disassembly is prohibited. DOCUMENTATION NOTICE The information contained in this document is subject to change without notice and should not be construed as a commitment by Motorola BCS. Motorola BCS assumes no responsibility for any errors that may appear in this document nor does it make an express or implied warranty of any kind with regard to this material, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. [. . . ] When your receiver has received the authorization message, the Trip Counter on the Installation Settings menu will advance. Completing the Receiver Connections to Your Entertainment System You will need to make changes to connect your VCR. · Connect the top/left TV terminal on the back panel of the receiver to the IN terminal on the VCR. If you had already connected this cable to your TV you must disconnect and connect it to your VCR. Connect the OUT terminal(s) on the VCR to the VHF IN terminal(s) on the TV. · 36 Installation Connections to Audio/Video Monitor Complete the following steps if you only plan to connect the receiver to an audio/ video monitor: · Using standard RCA-type audio/video cables, connect the top/left TV (VIDEO output) terminal on the rear panel of the receiver to the video input terminal on the monitor (or TV using the baseband inputs). Using standard RCA-type audio/video cables, connect the two bottom/left speaker (R and L) terminals on the back panel of the receiver to the audio input terminals on the monitor (or TV using the baseband inputs). · Connections to Audio/Video Monitor and VCR Complete the following steps if you plan to connect the receiver to an audio/video monitor and VCR: · Using standard RCA-type audio/video cables, connect the top/right TV (VIDEO output) terminal on the rear panel of the receiver to the video input terminal on the VCR. Using standard RCA-type audio/video cables, connect the two bottom/right speaker icon (R and L) terminals on the Rear Panel of the receiver to the audio input terminals on the VCR. · · Using standard RCA-type audio/video cables, connect the audio and video inputs on the audio/video monitor (or TV using baseband audio/video inputs) to the outputs on the VCR. If your entertainment center is enabled for Dolby Digital AC-3 Version 5. 1 (six channel) surround sound, connect this port to one end of the orange RCA cable and the other end of the orange RCA cable to your surround sound processor. · After you complete the installation procedures, you may wish to use the on-screen menus to make adjustments to the receiver's operation. DSR470 User Guide 37 4 Additional Features Options. It appears when you press the OPTIONS key on the remote control or when you press the MENU key on the receiver followed by selecting OPTIONS from the main Menu. System Settings. The System Settings menu provides access to menus which allow you to adjust the operation of your system. 38 Installation Viewing and Language Settings The Channel Information option allows you to turn the header (top of screen) and banner (bottom of screen) On or Off. The Subtitles option allows you to select the language for subtitles (if available for the particular program) or keep them turned off. The Language option allows you to select the language of the onscreen menus and audio for your programs. The TV Viewing option allows you to select the size of the viewing area. Select the Standard option if your TV screen is a typical screen with a 4:3 ratio of width to height. Select Wide if your TV screen is a wide screen with a 16:9 ratio (as in HDTV's or digital TV's). The default setting is Standard. DSR470 User Guide 39 4 Audio Settings If you are in CBL mode (digital) broadcast, three options appear on the Audio Settings menu. 1. Select option 1 (Audio Connections), and you will be able to select either TV or HiFi (the default is TV). Select TV if the receiver's AUDIO OUT port is connected to your TV. Select option 2 and then select Mono, Stereo, Surround or Dolby Digital (the default is Surround). Select Mono, Stereo or SAP (Secondary Audio Program) for your analog cable TV programming (channel numbers normally under 100). The default is Stereo. 40 Installation Installation Settings Channel Signal Strength. This option allows you to see the strength of the signal your system is receiving. Set Remote Control Address. This option allows you to control up to four receivers in a centralized area, with one or more remote controls. [. . . ] IN NO EVENT SHALL MOTOROLA BCS BE LIABLE FOR INDIRECT, EXEMPLARY, INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES (INCLUDING LOST PROFITS AND LOSS OF USE OR PAID TV TIME) BASED UPON BREACH OF WARRANTY OR CONTRACT, NEGLIGENCE, STRICT LIABILITY, OR ANY OTHER LEGAL THEORY. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation may not apply to you. NO AGENT, DEALER, DISTRIBUTOR, SERVICE CENTER, COMPANY, OR OTHER PERSON IS AUTHORIZED TO CHANGE, MODIFY, OR EXTEND THE TERMS OF THIS LIMITED WARRANTY IN ANY MANNER WHATSOEVER. This warranty gives you specific legal rights, and you may have other rights, which vary, from state to state. Calling for Service Before you call for service: · · · Unplug your receiver from the AC outlet, wait one minute, plug the receiver back in, and try to use it again. [. . . ]