User manual MOTOROLA H9 MINIBLUE HEADSET

[. . . ] When headset's battery is fully charged (about 3 hours), the Headset Battery indicator light turns off. Do not remove the headset from the charger base until step 3. Note: Once the headset is fully charged, the charger base will continue to charge. When fully charged (about 6. 5 hours), the Charger Battery indicator light turns off. Headset Battery Indicator Charger Battery Indicator Charger Plug 2 START BLUETOOTH FEATURE Your Phone 3 PAIR Your Headset Your phone's Bluetooth feature is off by default. To use your headset, you must turn on the Bluetooth feature in your phone. [. . . ] To make a call: USING YOUR PORTABLE CHARGER BASE The portable charger base provided with your headset can be used to cordlessly recharge your headset anywhere. Once charged, the portable charger base provides power on-the-go, extending your talk time by constantly "topping off" your headset's battery. Using the included Motorola power supply, you can charge both the portable charger base and headset at the same time. The portable base charger provides two indicator lights for charging status. See "Indicator Lights" in the reverse side of this guide for information on these indicator lights. Note: Using your PC's USB port as a power source for charging is not recommended. 1 Place the headset in your ear. The eartip should be inserted so that the headset feels comfortable and forms a seal in the ear. Note: See "Eartips and Your Headset" on the reverse side of this guide for more information on using eartips with your headset. 2 On the phone, dial the number you want to call and press SEND key on your phone. 3 If your phone and headset are successfully paired, you will hear ringing on the headset. After you have successfully paired your phone and headset, you don't need to repeat these steps. For daily use, ensure that your headset is turned ON and that your phone's Bluetooth feature is ON. USING YOUR H9 See Features and Functions Guide on the reverse side for information on using your H9 TROUBLESHOOTING My headset will not enter pairing mode. Make sure that any devices previously paired with the headset are turned off. If the indicator light is not steadily lit in blue, turn off both the other device and headset, wait 10 seconds, then turn headset back on. Wait for the indicator light to become steadily lit in blue, indicating the headset is now in pairing mode. Make sure the indicator light on your headset is on (lit in blue) and steady when your phone is searching for devices (see step 3). Make sure your phone is on and the Bluetooth feature is turned on in your phone (see step 2). If the Bluetooth feature was turned off or was turned on only temporarily, you may need to restart the Bluetooth feature (see step 2) and pair your phone and headset again (see step 3). If you need more help, contact us at 1-877-MOTOBLU or visit us at www. hellomoto. com/Bluetoothsupport Features and Functions Guide H9 Bluetooth® Handsfree Headset TURNING ON AND OFF To turn your headset on, press and hold the Call button until the indicator light flashes. To turn your headset off, press and hold the Call button until the indicator light flashes rapidly and then turns off. To conserve battery power, store your headset in the included charger base. IMPORTANT: Be sure to first follow the Quick Start Guide on the reverse side of this guide to complete initial setup of your H9. Indicator Light Call Button EARTIPS AND YOUR HEADSET Your H9 headset is supplied with multiple eartips. The eartip is fitted onto the end of your headset's earpiece speaker, and placed into your ear when using your headset. INSTALLING EARTIP When installing an eartip, carefully place it onto the tip of the earpiece speaker. 1 Pull back largest flange on eartip. 2 Twist eartip onto earpiece starting at an Flanged Tip Your headset's performance is greatly dependent upon achieving a good seal in your ear. [. . . ] Audio Tone Single high tone when pressing Volume button Five rapid high tones repeated every 20 sec. No audio indications; deteriorating quality Ring tone Single very high tone Headset Status Volume at minimum or maximum Low battery Out of range Incoming call All calls ended Put an active call on hold or resume a call on hold Transfer a call from the phone to the headset Transfer a call from the headset to the phone Mute or unmute a call Note: Some features are phone/network dependent. AUDIO TONES CONTINUED Audio Tone Single high tone Headset Status Tapping Call button or both Volume buttons Pressing Call button or both Volume buttons for 1-2 sec. Pressing and holding Call button or both Volume buttons for greater than 2 secs. Phone network not available Mute enabled Mute disabled Headset powering on Headset powering off INDICATOR LIGHTS Indicator lights provide information about your headset and charger base status. [. . . ]