User manual MOTOROLA QG-HS830

[. . . ] Release Tab Down For most Motorola phones: (Menu) 1 Press M( > Settings > Connection > Before you can use your wireless module, you must pair (link) it with your phone. Step A - PUT THE MODULE IN PAIRING MODE Indicator Light 1 Plug the Motorola charger into the end of the module with the release tab facing down. When the module's battery is fully charged (about 2 hours), the indicator light turns off. Bluetooth Link > Setup. 2 Scroll to Power. [. . . ] Make sure the indicator light on your wireless module is on and steady when your phone is searching for devices (see step 3). Make sure your phone is on and the Bluetooth feature is turned on in your phone (see step 2). If the Bluetooth feature was turned off or was turned on only temporarily, you may need to restart the Bluetooth feature (see step 2) and pair your phone and wireless module again (see step 3). FOR DETAILS ABOUT YOUR HANDSFREE DEVICE See the user's guide or visit us at www. hellomoto. com/bluetooth and click Support. Step B - SET YOUR PHONE TO LOOK FOR YOUR MODULE For most Motorola phones: (Menu) 1 On your Motorola phone, press M( > 1 Insert the 2. 5mm plug from the neck strap into the module jack on the bottom of the wireless module. Slots Your phone and wireless module are now paired and ready to make and receive calls. To make a call: Settings > Connection > Bluetooth Link > Handsfree > Look for Devices. 1 Place the neck strap on and the earbud in your ear. Plug Neck Strap Holder The phone lists Bluetooth devices it finds. 2 On your phone, dial the number you want to call and press the SEND key. 2 Select Motorola HS830. 3 Select OK or Yes to pair your module with your phone. Module Jack 3 If your phone and module are successfully After you have successfully paired your phone and module, you don't need to repeat these steps. For daily use, ensure that your module is turned ON and that your phone's Bluetooth feature is ON. To save battery power, turn OFF the module when you don't use it for an extended time. paired, you will hear ringing on the earbud. 4 Enter the passkey: 0000 5 Select OK. When your wireless module successfully pairs with your phone, the indicator light changes from steadily lit to flashing. Note: These steps are for most Motorola phones. For other phones, see your phone's user's guide. 2 Push the wireless module back into the neck strap holder. 3 Insert the two tabs on the neck strap holder into the slots on the top of the wireless module. neck and insert the earbud in your ear. 4 Place the neck strap around your © Motorola, Inc. 2005. TURNING ON AND OFF HS830 Bluetooth® Wireless Module To turn on the wireless module, press and hold the Call E button on your module until the indicator light begins flashing. To turn off the wireless module, press and hold the Call E button on your module for 5 seconds. The indicator light will flash rapidly and then stop flashing. ADJUSTING VOLUME To adjust the volume on your wireless module, press the Volume Up or Volume Down button until you reach the desired volume level. Volume Up Button Volume Down Button Function MAKING CALLS Action Tap the Call button and speak the name after the tone Tap the Call button Tap the Call button Press and hold the Call button until you hear a beep Press and hold the Call button until you hear a beep Press and hold both Volume buttons until you hear a beep. Press either Volume button Tap the Call button Make a voice dial call Receive a call End a call Reject a call Redial last call MAKING CALLS CONTINUED Function Answer a second incoming call Toggle between two active calls Join a 3-way call (Note: Feature is phone/ network dependent. ) Put an active call on hold or resume a call on hold Action Press and hold the Call button (places first call on hold) Press and hold the Call button Press and hold both Volume buttons Press and hold the Call button until you hear a beep IMPORTANT: Be sure to first follow the Quick Start Guide on the reverse side to complete initial setup of your HS830. Indicator Light Call Button Mute a call Unmute a call Transfer a call from the phone to the module Note: Your HS830 supports both Handsfree and Headset Profiles. [. . . ] Two wireless modules can also be configured for full-duplex voice communication with each other. For example, a motorcycle driver may communicate wirelessly with a rider sitting behind. For details on these applications, see the HS830 Helmet Adapter User's Guide. Power off The wireless module sounds an audible alert so that you do not miss an incoming call even if your phone is in a bag or briefcase. [. . . ]