User manual MOTOROLA SBV5121 SURFBOARD DIGITAL VOICE MODEM

[. . . ] User Guide SBV5121 VoIP Cable Modem Introduction Installation Troubleshooting Glossary License Safety and Regulatory Information WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. CAUTION: THIS PRODUCT WAS QUALIFIED UNDER TEST CONDITIONS THAT INCLUDED THE USE OF THE SUPPLIED CABLES BETWEEN SYSTEMS COMPONENTS. TO ENSURE REGULATORY AND SAFETY COMPLIANCE, USE ONLY THE PROVIDED POWER AND INTERFACE CABLES AND INSTALL THEM PROPERLY. CAUTION: DIFFERENT TYPES OF CORD SETS MAY BE USED FOR CONNECTIONS TO THE MAIN SUPPLY CIRCUIT. [. . . ] If that does not correct your problem, see the Regulatory, Safety, Software License, and Warranty Information card provided with your SBV5121 VoIP cable modem for information about obtaining warranty service. SBV5121 VoIP Cable Modem User Guide 14 Introduction Installation Troubleshooting Glossary License Setting Up a USB Driver in Windows 2000 1 2 Insert the SBV5121 VoIP Cable Modem CD-ROM in the CD-ROM drive. This CD contains the USB drivers and must be inserted and read by the PC before you connect the VoIP cable modem to the PC. For further instructions, see "Cabling and Startup for a Single User" on page 8. A few seconds after you complete the USB connection, the Found New Hardware Wizard window is displayed: 3 Click Next. The following window is displayed: Although your VoIP cable modem model number may be different than in the images in this guide, the procedure is the same. Be sure "Search for a suitable driver for my device" is selected. SBV5121 VoIP Cable Modem User Guide 15 Introduction Installation Troubleshooting Glossary License 4 Click Next. The following window is displayed: Be sure "CD-ROM drives" is the only box selected. 5 Click Next. If the Insert Disk window is displayed, be sure the SBV5121 VoIP Cable Modem CD-ROM is in the CD-ROM drive and follow steps 7 to 11. Otherwise, if the Completing the Found New Hardware window is displayed, you can skip to step 12. SBV5121 VoIP Cable Modem User Guide 16 Introduction Installation Troubleshooting Glossary License 7 On the Insert Disk window, click OK. The Files Needed window is displayed: 8 9 If necessary, select your CD-ROM drive in the "Copy files from" list. Click Browse. 10 Double-click the NetMotCM. sys file in the CD-ROM root directory. The Found New Hardware Wizard window is displayed: 12 Click Finish to complete the installation. When you finish setting up the USB driver, you can continue with "Configuring TCP/IP in Windows 2000" on page 23. If you have any difficulties setting up the USB driver, perform "Removing the USB Driver from Windows 2000" on page 38 and repeat this procedure. SBV5121 VoIP Cable Modem User Guide 17 Introduction Installation Troubleshooting Glossary License Setting Up a USB Driver in Windows Me 1 2 Insert the SBV5121 VoIP Cable Modem CD-ROM in the CD-ROM drive. This CD contains the USB drivers and must be inserted and read by the PC before you connect the VoIP cable modem to the PC. For further instructions, see "Cabling and Startup for a Single User" on page 8. A few seconds after you complete the USB connection, the Add New Hardware Wizard window is displayed: 3 Click Next. Windows automatically searches for the correct USB drivers and installs them. Otherwise, be sure the SBV5121 VoIP Cable Modem CD-ROM is correctly inserted in your CD-ROM drive. Although your SBV5121 VoIP cable modem model number may be different than in the images in this guide, the procedure is the same. 4 Click Finish to complete the installation. When you finish setting up the USB driver, you can continue with "Configuring TCP/IP in Windows 98 Second Edition, or Windows Me" on page 20. SBV5121 VoIP Cable Modem User Guide 18 Introduction Installation Troubleshooting Glossary License Setting Up a USB Driver in Windows XP 1 2 Insert the SBV5121 VoIP Cable Modem CD-ROM in the CD-ROM drive. This CD contains the USB drivers and must be inserted and read by the PC before you connect the VoIP cable modem to the PC. For further instructions, see "Cabling and Startup for a Single User" on page 8. A few seconds after you complete the USB connection, the Found New Hardware Wizard window is displayed: 3 4 Be sure "Install the software automatically" is selected. Windows automatically searches for the correct USB drivers and installs them. [. . . ] Motorola and its 3rd party licensors retain the ownership of the Software. You may: USE the Software only in connection with the operation of the Product. TRANSFER the Software (including all component parts and printed materials) permanently to another person, but only if the person agrees to accept all of the terms of this License. If you transfer the Software, you must at the same time transfer the Product and all copies of the Software (if applicable) to the same person or destroy any copies not transferred. [. . . ]