User manual MOTOROLA WIRELESS CABLE MODEM GATEWAY SBG900

[. . . ] User Guide SBG900 Wireless Cable Modem Gateway Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. CAUTION: TO ENSURE REGULATORY AND SAFETY COMPLIANCE, USE ONLY THE PROVIDED POWER AND INTERFACE CABLES. DO NOT CONNECT THE PLUG INTO AN EXTENSION CORD, RECEPTACLE, OR OTHER OUTLET UNLESS THE PLUG CAN BE FULLY INSERTED WITH NO PART OF THE BLADES EXPOSED. DO NOT PERFORM ANY SERVICING OTHER THAN THAT CONTAINED IN THE INSTALLATION AND TROUBLESHOOTING INSTRUCTIONS. [. . . ] This number of frames received with the WEP subfield of the Frame Control field set to one and the WEP On key value mapped to the client MAC address. This indicates that the frame should not have been encrypted or was discarded due to the receiving client not having WEP enabled. Click to collect new data. Refresh Home Print Exit X 77 SBG900 User Guide Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB Setting Up a USB Driver The following subsections describe setting up a USB driver if you connect a PC to the USB port on the SBG900. Perform one of the following procedures based on your Windows version: · · · · Setting Up a USB Driver in Windows 98 Setting Up a USB Driver in Windows 2000 Setting Up a USB Driver in Windows Me Setting Up a USB Driver in Windows XP The SBG900 USB driver does not support Macintosh or UNIX computers. For those systems, you can connect through Ethernet only. Caution! Be sure the Motorola SURFboard Wireless Cable Modem Gateway CD-ROM is inserted in the CD-ROM drive before you plug in the USB cable. If you have a problem setting up the USB driver, remove it by performing one of the following procedures: · · · Removing the USB Driver from Windows 98 or Windows Me Removing the USB Driver from Windows 2000 Removing the USB Driver from Windows XP Home Print Exit X 78 SBG900 User Guide Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB Setting Up a USB Driver in Windows 98 1 Insert the Motorola SURFboard Wireless Cable Modem Gateway CD-ROM in the CD-ROM drive. This CD contains the USB drivers and must be inserted and read by the PC before you connect the SBG900 to the PC. Connect the USB cable as shown in USB Connection. A few seconds after you complete the USB connection, the Add New Hardware Wizard window is displayed: 2 3 Click Next. The following window is displayed: 4 Be sure "Search for the best driver for your device" is selected. Home Print Exit X 79 SBG900 User Guide Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB 5 Click Next. The following window is displayed: Be sure "CD-ROM drive" is the only box checked. 6 Click Next. The message "Please wait while Windows searches for a new driver for this device" is displayed. If the computer successfully locates the driver, you can skip to step 9. If the computer does not locate the driver, the previous window is displayed again. 7 Select Specify a location and type the location of the CD-ROM drive: To load the driver successfully, you may need to click Browse to manually select the NetMotCM. sys file on the CD-ROM. Home Print Exit X 80 SBG900 User Guide Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB 8 Click Next. The following window is displayed: 9 Select The updated driver. . . If the following window is not displayed, verify that the Motorola SURFboard Wireless Cable Modem Gateway CD-ROM is properly inserted in the CD-ROM drive. If you still cannot find the correct driver file, click Cancel to cancel the installation and perform the procedure for "Removing the USB Driver from Windows 98 or Windows Me". Then repeat this procedure. Although your SBG model number may be different than in the images in this guide, the procedure is the same. 10 After the window shown under step 9 is displayed, click Next. If a window with the message Copying Files. . . displays and asks for the CD-ROM drive, type the CD-ROM drive letter (for example, "D:") and click OK. If an Insert Disk window similar to the one below is displayed, Windows 98 system files are needed to complete the installation. To install the files, insert your Windows 98 CD-ROM in the CD-ROM drive and click OK. Home Print Exit X 81 SBG900 User Guide Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB After all the necessary files are loaded, the following window is displayed to confirm a successful installation: 11 Click Finish. The Systems Settings Change window is displayed: 12 Click Yes to restart the computer. When you finish setting up the USB driver, you can continue with "Configuring TCP/IP". If you have difficulties setting up the USB driver, perform "Removing the USB Driver from Windows 98 or Windows Me" and repeat this procedure. If that does not correct the problem, see the Regulatory, Safety, Software License, and Warranty Information card provided with the SBG900 for information about obtaining warranty service. Home Print Exit X 82 SBG900 User Guide Overview Installation Troubleshooting Contact FAQ Specifications Glossary License Configuration: Basic Gateway TCP/IP Wireless USB Setting Up a USB Driver in Windows 2000 1 Insert the Motorola SURFboard Wireless Cable Modem Gateway CD-ROM in the CD-ROM drive. [. . . ] Motorola and its 3rd party licensors retain the ownership of the Software. You may: USE the Software only in connection with the operation of the Product. TRANSFER the Software (including all component parts and printed materials) permanently to another person, but only if the person agrees to accept all of the terms of this License. If you transfer the Software, you must at the same time transfer the Product and all copies of the Software (if applicable) to the same person or destroy any copies not transferred. [. . . ]