User manual MOTOROLA WIRELESS PRINT SERVER-WPS870G

[. . . ] WPS870G Regulatory, Warranty, and Copyright Information User Guide WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. CAUTION: TO ENSURE REGULATORY COMPLIANCE, USE ONLY THE PROVIDED POWER AND INTERFACE CABLES. DO NOT PERFORM ANY SERVICING OTHER THAN THAT CONTAINED IN THE INSTALLATION AND TROUBLESHOOTING INSTRUCTIONS. To comply with the FCC RF exposure compliance agreements, the separation distance between the antenna and any person's body (including hands, wrists, feet, and ankles) must be at least 8 inches (20 cm). [. . . ] Windows 2000 and XP require no additional software. PAGE 53 WPS870G Windows 98SE/ME IP Printer Port Setup This section installs the IPP client and configures your port for IP printing. Navigate to the IPP folder and double-click the IPP_Client. exe file to install the program. Once finished, navigate to the program by clicking Start > Programs > IPP Port Monitor > Add IPP Port. The Configure IPP Port window is displayed: 3 In the IP address field, type the IP address or URL of the WPS870G. If using a Proxy Server, enter the necessary information (this will be the same as your browser configuration). Click Select Device Port to view the available ports on the WPS870G, and select the appropriate port. Click Save. 4 5 PAGE 54 User Guide The AddPort window is displayed: WPS870G 6 If desired, you can click Add New Printer to add a new printer for the IP port. To print from any application, select the printer configured for the port. Click OK to exit. Note: If using the Epson Spooler Manager, this program must be disabled, as follows: 1 2 3 4 PAGE 55 WPS870G Windows 2000/XP IP Printer Port Setup The recommended printing method is to use the LPR protocol for IP printing: 1 User Guide Open your Printers folder (usually Start > Settings > Printers), right-click the desired printer and select Properties. The Properties window is displayed: 2 3 Select the Ports tab and click Add Port. Choose Standard TCP/IP Port and then click New Port. PAGE 56 User Guide The Add Standard TCP/IP Printer Port Wizard window is displayed: WPS870G 4 Enter the IP Address of the Print Server in the Printer Name or IP address field and click Next. The Additional Port Information Required window is displayed: 5 Select Custom and click Settings. PAGE 57 WPS870G The Configure Standard TCP/IP Port Monitor window is displayed: User Guide 6 On the Port Settings tab: ­ ­ ­ Select LPR Enter a Queue name (L1 for Port 1 (Parallel), L2 for Port 2 (USB)) Ensure the LPR Byte Counting Enabled setting is selected. 7 Click OK to confirm your changes and close this window. IP printing is now enabled. Print Jobs Management Print jobs can be managed like any Windows printer. Open the Printers folder (Start > Settings > Printers) and double-click any printer to see the current print jobs. If the printer attached to the WPS870G has been changed (for example its driver has been updated), run the Add IPP Port program again and select the correct printer. Delete a Printing Port If the WPS870G's IP address has changed, and you can no longer print, delete the WPS870G's port and re-install it. To delete a port, use the Windows Delete Port facility: 1 2 Right-click any printer in the Printers folder and select Properties. On the Details or Ports tab (depending on your version or Windows), locate and click Delete Port. PAGE 58 User Guide WPS870G 3 If Windows responds that a printer is still using the port, apply another port to the selected printer and try deleting the port again. Advanced Port Options 1 2 3 Click Start > Settings > Printers to open the Printers folder. On either the Details or Ports tab (depending on your version of Windows), click Port Settings. A window is displayed (the window on your system may differ slightly from the example below): Items shown on this window are as follows: Port If desired, click Browse to select a different Wireless Print Server. If the selected device has multiple ports, use Select Device Port to select the port. Retry Interval Sets how often Windows polls the Wireless Print Server to establish a connection when the printer is busy. [. . . ] Subscriber A user who accesses television, data, or other services from a service provider. PAGE 104 User Guide WPS870G Subnet Mask A methodology that determines what the router will examine for the destination of an IP address. Switch On an Ethernet network, a switch filters frames based on the MAC address, in a manner similar to a bridge. A switch is more advanced because it can connect more than two segments. T TCP Transmission Control Protocol on OSI Transport Layer 4 provides reliable transport over the network for data transmitted using IP (network layer three). It is an end-to-end protocol defining rules and procedures for data exchange between hosts on top of connectionless IP. [. . . ]