User manual NAVMAN FISH 4100

[. . . ] FISH 4100 / 4150 Installation and Operation Manual English . . . . . . . . . . . . . c o m NAVMAN FCC Statement Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a normal installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. [. . . ] Both logs are retained in the fishfinder memory when the FISH 4150 is switched off. Use the SETUP - LOG menu to select the Trip Log or Total Log (see section 4-6). to record total mileage during a season, or the distance travelled on this trip). Note that the units displayed on each Log will correspond with the Speed. Speed can be displayed in knots (KN), miles per hour (MPH), or kilometres per hour (KPH). Use the SETUP - UNITS - SPEED menu to select the desired speed units (see section 4-2). Enabled Alarms A graph displays the surface water temperature for the last 40 minutes and is updated every 30 seconds. The current water temperature is displayed above the graph and is updated every second. Depth 3-8 RANGE menu Select MAIN MENU - RANGE to change the manual range and adjust the selected depth range. This shows the depth of water displayed vertically and the range mode setting. The NAVMAN fishfinder has two range modes, Auto Range and Manual Range. The Manual Range mode offers the user a choice of pre-selected water depths. Press to exit. FISH 4100 Installation and Operation Manual NAVMAN 13 4 SETUP menu Use the SETUP menu to customize the NAVMAN fishfinder to suit the boat and individual preferences. On a FISH 4100 use the SETUP menu to: Specify the trigger settings for the alarms (4-1). Press or to select an option: · · · · On a FISH 4150 use the SETUP menu to: · · Specify the trigger settings for the alarms (4-1). · Select language, setup keel offset and calibrate speed and temperature sensors (4-7, 4-8). Press or to select an option: 4-1 ALARMS menu Select MAIN MENU - SETUP - ALARMS to display the available alarms. Alarms can be enabled to automatically detect certain conditions, such as the water being too shallow. Trigger settings can be defined to suit the boat and individual preferences. The FISH 4100 ALARMS menu is shown: The FISH 4150 has two extra alarms, TEMP VALUE and TEMP RATE. All of the alarm symbols and beeper cycles on the FISH 4100 are shown: Symbol Alarm Beeper Alarm condition is Name Cycle met when: 1/5 sec the depth is less than Too Shallow the alarm trigger value 1/2 sec Too the depth is greater Deep than the alarm trigger value Fish 3 short an echo matches the Alarm beeps profile of a fish 1/2 sec Low the battery voltage is Battery less than the alarm trigger value 14 The alarm symbols and beeper cycles for the two extra alarms on the FISH 4150 are shown: Symbol Alarm Beeper Alarm condition is Name Cycle met when: Temp 1/2 sec the temperature equals Value the alarm trigger value Temp 1/2 sec the rate of change of Rate temperature equals the alarm trigger value When an alarm condition is met, then: The beeper sounds. The ALARMS menu is displayed on the screen with the activated alarm symbol(s) flashing. Press any key to acknowledge the alarm, stop the beeping and remove the ALARMS menu. [. . . ] Ph: +34 93 750 75 04 Fax: +34 93 750 75 34 e-mail: plastimo@plastimo. es Website: www. plastimo. es Other countries in Europe PLASTIMO INTERNATIONAL 15, rue Ingénieur Verrière BP435 56325 Lorient Cedex, France. Ph: +33 2 97 87 36 59 Fax: +33 2 97 87 36 29 e-mail: plastimo. international@plastimo. fr Website: www. plastimo. com REST OF WORLD / MANUFACTURERS NAVMAN NZ Limited. Ph: +64 9 481 0500 Fax: +64 9 480 3176 e-mail: marine. sales@navman. com Website: www. navman. com ASIA China Peaceful Marine Electronics Co. E210, Huang Hua Gang Ke Mao Street, 81 Xian Lie Zhong Road, 510070 Guangzhou, China. [. . . ]