User manual NAVMAN ICN600

[. . . ] iCN 600 series with Smart TM 2005 User Manual iCN 630 iCN 635 iCN 650 English - United States / Canada iCN 600 series | User Manual Contents Box Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iCN Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Positioning the iCN in a Vehicle. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Press OK to confirm your selection. 39 iCN 600 series | User Manual 12. Avoiding an Area You can calculate a route that avoids a specified area on the map. If no alternative route around an Avoid Area exists, you will be routed through an Avoid Area. Adding an Avoid Area 1. Press OK and use the 8-way toggle to place the cross-hair over the area that you want to avoid. Set the Avoid Area to the correct size and position using the 8-way toggle. Press OK and use the 8-way toggle to place the cross-hair over the Avoid Area that you want to delete. To return to the Main Menu, press . 40 iCN 600 series | User Manual 13. Route Demonstrator The Route Demonstrator allows you to: · Preview a route. · Plan and view a route without a GPS fix, such as when you are inside a building. Step One: Activate Route Demonstrator 1. The Main Menu screen will display. Step Two: Select Departure Point If you have a GPS fix, you do not need to select a departure point unless you want the demonstrated route to start elsewhere. Where the cross-hair intersect on a street, the street name will display at the bottom of the 2D Map screen. The Pop-up menu will close. Step Three: Select Destination Point Set a destination either by using the Destination screen (see pages 17-25) or by using the 2D Map screen Pop-up menu by completing the following: 1. Where the cross-hair intersect, with a street, the street name will display at the bottom of the 2D Map screen. The 3D Map screen will display the calculated route in Route Demonstrator mode. · If you have selected the Repeat check box on the Routing screen, the Route Demonstrator will continue to repeat the route. 41 iCN 600 series | User Manual To Disable Route Demonstrator 1. The Main Menu screen will display. 42 iCN 600 series | User Manual 14. Favorites and My Home You can save up to 200 destinations as Favorites, one of which can be saved as My Home. My Home can be any designated Favorite, but we recommend that it is your home or other common destination. You can save a Favorite from the Preview screen after searching for an address, or from the Pop-up Menu on the 2D Map screen. Saving a Favorite 1. Either search for an address using the Destination and Keyboard screens as described in Setting Your Destination, pages 17-25, or create a multi-stop trip as described in Multi-stop Trips, pages 27-33, until the Preview screen is displayed. To change the name of the Favorite, select the Name box, then press OK. The Enter text screen will display. · Use the 8-way toggle to move around the Enter text screen. [. . . ] The POI Options window will open. 67 iCN 600 series | User Manual 3. Note: If you do not activate the POI, you will be able to configure only the POI Visibility Level and Icon File settings. enable a visual warning when the POI is in close proximity enable a warning chime when the POI is in close proximity change the units used to measure distance for this POI select the distance from the POI at which the visual warning should display or the warning chime should sound indicate the priority of this POI when one or more additional POIs are in the same locale select a custom POI type icon to display on the map (if you do not select a custom icon, a default icon will display) select the Visual Alert check box. select the distance from the Distance box. move the POI Visibility Level slider left or right. Type the path to the icon file to be used to represent the POI type, in the Icon File box, or select the icon file from your local or network , locating the file and clicking drive clicking Open. [. . . ]