User manual NAVMAN MULTI 3100

[. . . ] MULTI 3100 Installation and Operation Manual DRAFT Approved by translator Approved by Plastimo This document is still under review and is subject to change. c o m NAVMAN MULTI 3100 Installation and Operation Manual NAVMAN 1 FCC Statement Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a normal installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. [. . . ] The distance travelled since total log was reset: The log units are NM, KM or M (miles) and correspond to the speed units, for example if you set the speed units to KPH then the log units are KM (see section 3-1). 4-1 Reset log Resetting zeros the log (trip distance): 1 2 Press Press until LOG is displayed. + . 4-2 Reset total log Total log Resetting zeros the total log (total distance), as well as the log and avg speed: 1 2 NAVMAN MULTI 3100 Installation and Operation Manual Press Hold + until TOTAL LOG is displayed. for 5 seconds. 9 5 Depth, keel offset, too deep alarm, too shallow alarm Depth and keel offset The displayed depth is the distance from the transducer on the boat to the bottom of the water, plus or minus an offset which is called the keel offset: A positive keel offset displays depth as measured from a point above the transducer. For example, if you set the offset as the distance from the transducer to the surface, it Keel offset Water surface Depth of transducer Transducer Note: The boat illustrated uses a through hull transducer Keel offset Positive value Negative value will display the depth from the surface to the bottom of the water. A negative keel offset displays depth as measured from a point below the transducer. For example, if you set the negative offset as the distance from the transducer to the bottom of the keel, it will display the depth from the bottom of the keel to the bottom of the water. 5-1 Set depth units The units can be METERS, FEET or FATH: Press until DEPTH is displayed, then hold until the units change; if necessary, hold until the units change again. Shallow alarm value 5-2 Set too deep alarm The too deep alarm sounds if the alarm is turned on and the depth becomes equal to or more than the too deep alarm depth. To set the too deep alarm: 1 Hold for two seconds to display the Too Deep Alarm screen: 2 3 4 Alarm is off To change the alarm depth, press or To turn the alarm on or off, press . . 5-4 Anchor watch To set an anchor watch, set the too shallow alarm to slightly less than the current depth and set the too deep alarm to slightly more than the current depth. Allow for tide changes. Deep alarm value Alarm is on 2 3 4 To change the alarm depth, press To turn the alarm on or off, press Press . The range is ± 2. 9 m (± 9. 6 ft, ± 1. 6 fathoms): Keel offset (negative) 5-3 Set too shallow alarm The too shallow alarm sounds if the alarm is turned on and the depth becomes equal to or less than the too shallow alarm depth. To set the too shallow alarm: 1 At the Too Deep Alarm screen, hold for two seconds to display the Too Shallow Alarm screen: 1 2 3 Press + several times until the Keel Offset screen is displayed: or to change the keel offset. Press Press . NAVMAN MULTI 3100 Installation and Operation Manual 10 6 Temperature Temperature is measured by a sensor in the speed transducer. 6-1 Set temperature units The units can be either °C or °F: Press until the temperature is displayed, then hold until the units change. Water temperature 6-2 Calibrate temperature The unit is factory calibrated and should not normally need calibrating. To calibrate: 1 2 Measure the water temperature near the speed transducer. Press + several times until the Temperature Calibration screen is displayed: 3 4 or to change the temperature to Press the value measured in step 1 above. Press . 7 Countdown timer You can adjust the countdown timer to start counting down between one and ten minutes, in increments of one minute. When the timer is counting down, the countdown timer symbol flashes and the time remaining is displayed in minutes and seconds: Countdown timer symbol flashes Timer counting down The beeper sounds and any external beepers or lights operate: Four beeps at four minutes to go. Ten beeps at the end; the last beep is longer and marks the end of the countdown. 2 3 Press or Timer start time is 9 min to set the start time in minutes. 7-2 Stop and reset countdown timer 1 2 Press until the countdown timer is displayed. The timer stops and the time resets to the start time (see section 7-3). Press + several times until the Countdown Timer Start Time screen is displayed: 7-3 Adjust start time 1 Press . The timer does not start now (to start the timer, see section 7-1). 7-1 Start countdown timer The timer starts at the start time (to adjust the start time, see section 7-3). The timer displays On briefly and starts counting down from the start time. MULTI 3100 Installation and Operation Manual 11 NAVMAN 8 Systems of several instruments Several NAVMAN instruments can be connected together during installation to share data. [. . . ] Ph: +31 182 320 522 Fax: +31 182 320 519 e-mail: info@plastimo. nl Website: www. plastimo. nl United Kingdom PLASTIMO Mfg. School Lane - Chandlers Ford Industrial Estate, EASTLEIGH - HANTS S053 ADG. Ph: +44 23 8026 3311 Fax: +44 23 8026 6328 e-mail: sales@plastimo. co. uk Website: www. plastimo. co. uk Sweden, Denmark or Finland PLASTIMO NORDIC AB. Ph: +46 304 360 60 Fax: +46 304 307 43 e-mail: info@plastimo. se Website: www. plastimo. se Spain PLASTIMO ESPAÑA, S. A. [. . . ]