User manual NAVMAN S300

[. . . ] 5 min before automatic shutdown** * Press and hold to perform a controlled shutdown. ** When battery power becomes too low to continue operation, a controlled shutdown is automatically executed (current data is saved). S300 1-7 S300 - Interface NAVMAN 2. 0 Navman S300 interface 2. 1 Button functions There are two control buttons, and . These buttons are pressed separately or together to turn the unit on and off, cycle through modes, and select mode options. Throughout this guide the button icons are used as follows: = press this button = press this button = press both buttons together Note: where it is required to press and HOLD buttons, a countdown begins. To perform the required action continue to hold until the counter reaches zero; if you release the button sooner the action will not be performed. 2. 2 Display screen MIN MAX kmmi PM km/hmph 2 MAX AVG 8 7 3 ZONE SYSTEM SET SET The illustration above shows the complete display capability of the S300. [. . . ] When beep is ON, an audible `beep' will sound when buttons are pressed. status SYSTEM SET Access this option If necessary, press and hold to turn the power on and enter setup. 3) Press 4) Press to go to the next option, or hold to leave setup. 4. 1. 4 Set speed units Set units for speed (km/h or mph). km km/h SYSTEM SET speed units Access this option If necessary, press and hold to turn the power on and enter setup. 4) Press to go to the next option, or hold to leave setup. Note: Distance is displayed in units that correspond to user selected speed units. For example, if you select speed units `km/h', then distance is displayed in `km'. S300 1-13 S300 - Setup NAVMAN 4. 1. 5 Set offset (set local time) This option lets you adjust the S300 to display local time*. You only need to do this once, unless operating the unit in a new time zone. The S300 will perform all functions accurately without adjusting the offset to display your local time. ) Note: If you attempt to change the time offset before all GPS data are obtained, the screen displays `no GPS' and the antenna icon flashes until all GPS data are received. SYSTEM SET Access this option If necessary, press and hold to turn the power on and enter setup. To set local time to start editing (the screen now appears as shown 1) Press below). The date is displayed to ensure that adjustments are made in the correct direction. current time current date PM SYSTEM SET 2) Press repeatedly to set time display forward (press and hold to set time display forward quickly), or press repeatedly to set time display backward (press and hold to set time display backward quickly). 4) Press to go to the next option, or hold to exit setup. 1-14 S300 NAVMAN S300 - Setup 4. 1. 6 Editing settings (overview) settings edit editing details set 12hr set 24hr accept set (12hr) set (12hr) set (31-12) edit set (31-12) set 31-12 set 12-31 accept beep edit beep beep ON beep OFF accept set units (km/h) edit set units (km/h) set units (km/h) accept set units (mph) edit accept set offset time (date) KEY = press this button = press this button = press both buttons together S300 1-15 S300 - Normal operation NAVMAN 5. 0 Normal operation 5. 1 Modes Press to turn the power on and start normal operation. Press repeatedly to step through the modes (press and hold to cycle through the modes quickly). Modes are accessed in the order shown below. Press repeatedly until the screen appears as shown above. To set Zone status to start editing (zone status flashes). 3) Press 4) Press to go to the next mode. 5. 1. 5. 1 Zone (Minimum) This option lets you set the minimum target speed. target speed (MIN) MIN km/h ZONE SET Access this mode See section 5. 1. 5 for access to this mode. 2) Press repeatedly to increase value by 0. 5 (hold to increase values quickly), or press repeatedly to decrease value by 0. 5 (hold to decrease values quickly). 4) Press to go to the next mode. S300 1-19 S300 - Normal operation NAVMAN 5. 1. 5. 2 Zone (Maximum) This option lets you set the maximum target speed. target speed (MAX) km MAX km/h Access this mode See section 5. 1. 5 for access to this mode. 1) Press 2) Press repeatedly to increase value by 0. 5 (hold to increase values quickly), or press repeatedly to decrease value by 0. 5 (hold to decrease values quickly). 3) Press 4) Press to go to the next mode. 1-20 S300 NAVMAN S300 - Normal operation 5. 1. 6 Clock mode Clock mode shows the current time and date. See section 4. 1. 5 for instructions on setting local time. ) current time current date PM Access this mode If necessary, press to turn the power on and start normal operation. Press repeatedly until the screen appears as shown above. While in Clock mode to clear all* session data. · Press to go to the next mode. Note: If GPS signals are not yet obtained a `no GPS' alert is displayed. The antenna icon flashes until GPS signals are received. S300 1-21 S300 - Normal operation NAVMAN 5. 1. 7 Timer mode Timer mode lets you monitor session time. session time Access this mode If necessary, press to turn the power on and start normal operation. Press repeatedly until the screen appears as shown above. While in Timer mode to clear all* session data. (*Does not clear · Press and hold odometer. ) · Press to go to the next mode. Note: The timer starts automatically whenever you start moving and stops whenever you stop moving. 1-22 S300 NAVMAN S300 - Normal operation 5. 1. 8 Mode operation (overview) modes Speed operating details clear all session data* clear all session data* edit AVG Speed (AVG) MAX Speed (MAX) clear max speed only 2 873 Odometer clear odometer only accept ZONE SET Zone OFF Zone OFF Zone OFF Zone ON accept Zone ON edit accept edit Zone MIN Zone MIN accept edit Zone MAX Zone MAX Clock clear all session data* clear all session data* Timer (*Does not clear odometer. ) * KEY = press this button = press this button = press both buttons together = press and hold both buttons together S300 1-23 S300 - Default settings NAVMAN 6. 0 Restoring default settings ! WARNING: Restoring factory default settings clears all stored data and all user selected settings! To restore all default factory settings 1) make sure the unit is off 2) press and hold to turn the unit on ­ DO NOT RELEASE 3) while holding , press five times When restoring default settings The screen displays the message `reset all' and a counter. [. . . ] SOME STATES AND COUNTRIES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE WARRANTY PERIOD MAY NOT APPLY TO YOU. Each of these disclaimers is in addition to, and does not reduce the effect of, any other disclaimer. No event that voids any warranty of the Product will have any effect on these disclaimers or limitations of liability. This disclaimer will be construed under the laws of New Zealand without regard for any conflict of law rules. [. . . ]