User manual NAVMAN TRACKER 5430

[. . . ] Pilot 3380 Tracker 5430/5430i AU C H A R T PT LO O P T I T L E O R T Installation and Operation Manual www. navman. com FCC Statement Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a normal installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. [. . . ] Edit the route as described in section 10-2-1 B, starting at step 3. Editing a route from the routes display 1 2 3 As waypoints are inserted, the distance and bearing of each leg is shown automatically. If the route has more waypoints than will fit on the display, press or to see them. 5 i ii 6 7 8 To remove a waypoint from the route: Select the waypoint to remove. Display the route on the chart (see section 10-2-3) and check that the route does not cross land or dangerous water. 10-2-3 Displaying a route on the chart This goes to the chart display, and shows the selected route at the centre of the display. Select Yes to confirm. 2 10-2-4 Deleting a route 1 10-2-2 Editing a route Editing a route from the chart 1 In the routes display, select the route to edit. Press MENU and select Edit on chart. 2 1 2 10-2-5 Deleting all routes 10-3 Navigating a route 10-3-1 Starting a route To start the boat navigating along a route: 1 In the routes display, press or to highlight the route to use. 3 It displays a chart with the route marked and starts navigating from the start of the route. 10-3-2 Skipping a waypoint in a route To skip a waypoint when the boat is navigating along a route: In the chart display, press MENU and select Skip. The TRACKER starts navigating straight towards the next waypoint on the route. Warning: Skipping a waypoint with the autopilot on might result in a sudden course change. 2 10-3-3 Cancelling a route To stop the boat navigating along a route: In the chart display, press MENU and select Cancel route. 24 NAVMAN TRACKER 5430/5430i Installation and Operation Manual 11 User card display A C-MAPTM user card is an optional plug-in card that can store data files (see section 1-2). The user card display has: File list A list of the files on any user card in the TRACKER. Waypts, Routes The number of waypoints and routes currently in the TRACKER. Track 1 to Track 5 The number of points in tracks 1 to 5 currently in the TRACKER. Note: To save TRACKER data onto the user card, use the Save command (see below). Data stored on the user card and shown on the file list is not available to be used by the TRACKER until loaded into the TRACKER with the LOAD command (see below). Skip: Do not load the new waypoint. Skip all: Do not load any new waypoints which have the same names as existing waypoints. all: Load all new waypoints which have the same names as existing waypoints; the new waypoints replace the existing waypoints. A routes file: The new routes are added to any existing routes in the TRACKER. If a new route has the same name as an existing route but has different data then the TRACKER asks which route to keep. A track file: The new track will replace the existing track in the TRACKER. Press MENU and select Load. Saving TRACKER data to the user card This saves all the TRACKER's waypoints, all the TRACKER's routes or one of the TRACKER's tracks to one file on the user card. The new file appears in the file list. Loading data from the user card to the TRACKER This loads one file from the user card to the TRACKER: A waypoints file: The new waypoints are added to any existing waypoints in the TRACKER. If a new waypoint has the same name as an existing waypoint but has different data, the TRACKER displays both waypoints. [. . . ] Reset to factory defaults (see section 13-1). 41 NAVMAN Appendix C - Glossary and navigation data Glossary Attention Area - An important area on a chart, such as a restricted anchorage or a shallow area (see section 13-2). Chart card - A plug-in card that stores chart data for a region (see section 1-2). MOB function - Starts navigating back to the place where someone fell overboard (see section 2-4). NavBus - A way of connecting NAVMAN instruments together to share data (see section 14). [. . . ]