User manual NAVMAN TRACKER 950

[. . . ] C H A TRACKER950 R T P L O T T E R Installation and Operation Manual English. . . . . . . . . . . . . . . 4 Français. . . . . . . . . . . 44 w w w. c o m NAVMAN ® Contents 1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 1-1 Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 1-2 C-MAPTM chart cartridges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] When the cursor is over a waypoint, the softkeys are: Edit: Change the waypoint data (see section 6-1-6). List: List the waypoints (see section 6-1-9). 20 NAVMAN TRACKER950 CHARTPLOTTER Installation and Operation Manual 6-1-3 Create a new waypoint at the cursor or boat position 1 In the Waypoints screen: to create the new waypoint at the cursor position, move the cursor to the desired position and press the Save+ key to create it at the boat position, press the Save key 2 To save as a waypoint, press the Waypt key. Then press the Esc key to return to the Waypoints screen. To edit the waypoint data: 1 2 3 Press the CursorUp or CursorDown keys to highlight the piece of data to change. To change the data, press the CursorLeft or CursorRight keys to highlight the character to change, then press the CursorUp or CursorDown keys to change the character. Repeat this until all characters are correct, then press the Enter key. Press the Save key. 3 6-1-4 Create a new waypoint at a specified position 1 In the Waypoints screen, press the Create key to display a new waypoint edit window. Edit the waypoint data as described in section 6-1-6, then press the Save key. 2 6-1-5 Find a waypoint This moves the chart so that an existing waypoint is displayed on the chart: 1 In the Waypoints screen, move the cursor so that it is not over a waypoint. Press the Enter key. 6-1-7 Move a waypoint 1 2 3 4 In the Waypoints screen, move the cursor to the waypoint. Press the Save key. 2 6-1-6 Edit a waypoint You have the opportunity to edit the data for a waypoint in a number of screens. A window with the waypoint data appears: 6-1-8 Delete a waypoint You can not delete a waypoint if it is part of a route or if the boat is going to it. In the Waypoints screen: move the cursor to the waypoint, then press the Delete key. From the list of waypoints (see section 6-1-9): use the cursor keys to highlight the waypoint, then press the Delete key. 6-1-9 List the waypoints In the Waypoints screen, press List to display a list of all the waypoints. Waypoints that are being used can not be edited or deleted. NAVMAN TRACKER950 CHARTPLOTTER Installation and Operation Manual 21 Use the cursor keys to highlight a particular waypoint. These softkeys keys are available: Edit: Edit the data for the highlighted Waypoint (see section 6-1-6). You can not delete a waypoint if it is part of a route or the boat is going to the waypoint. View: Display the chart with the waypoint in the centre of the screen. GoTo: Start the boat going to the waypoint (see section 4-1). 22 NAVMAN TRACKER950 CHARTPLOTTER Installation and Operation Manual 6-2 Routes 6-2-1 Introduction to routes A route is a list of waypoints that the boat can navigate along. A route can start and stop at the same waypoint; in this case there must be three or more waypoints in the route. The boat can start at any waypoint in the route and can travel along a route in either direction. Routes are a particularly powerful feature when the TRACKER950 is connected to an autopilot, allowing the vessel to be automatically guided along the route. Make sure that any routes that you create do not cross land or any dangerous water. List: Display a list of the routes, see section 6-2-5). 6-2-3 Create a new route by selecting waypoints from a list 1 2 In the routes screen, press the TxtCrt key to display a new, empty route list. [. . . ] The route has a start and end waypoint and can be traversed from start to finish or in reverse. There can be up to 25 routes, each with up to 50 waypoints (see section 6-2). This is not necessarily the same as the boat speed through the water nor the speed at which it is approaching the destination. Waypoints are displayed on the chart as one of 12 icons with the name below. [. . . ]