User manual NAVMAN VHF 7000

[. . . ] VHF 7000, 7100US, 7100EU Operation Manual www. navman. com NAVMAN FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide a reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. [. . . ] Use + or - to step through the channels with their name tags until you see the channel name tag you want to change, then press ENT. In this example, the channel name TELEPHONE associated with channel 01 is being changed to PHONE1. It can be a maximum of 12 characters. To delete the channel name, select DELETE and press ENT. 18 NAVMAN VHF 7000, 7100US, 7100EU Operation Manual 4. Press ENT (repeatedly if necessary) to display the YES/NO confirmation. Press ENT to confirm the new channel name tag or the deletion, then press ESC to return to the menu. 3-3 RING & BEEP Volume (RING VOLUME) & (BEEP VOLUME) Set the volume level of the incoming signal beeps (RING VOLUME) and/or the error and warning beeps (BEEP VOLUME) to HIGH (high) or LOW (low) as follows: RADIO SETUP CH NAME >RING VOLUME BEEP VOLUME RING VOLUME >HIGH LOW BEEP VOLUME >HIGH LOW OFF 1. (It is possible to turn the beeps off completely by selecting BEEP VOLUME then OFF. ) 3. Press ENT to enable the new volume setting and return to the menu. 3-4 Internal Speaker Connections (INT SPEAKER) Switch the radio's internal speaker ON (on) or OFF (off). The external speaker is always ON (on) if a speaker is plugged into the external speaker jack. SETUP, then INT RADIO SETUP RING VOLUME BEEP VOLUME >INT SPEAKER INT SPEAKER >ON OFF 2. Select ON (on) or OFF (off) then press ENT to enable the setting and return to the menu. 3-5 Set the Priority Channel (WATCH MODE) If you have a VHF7000 or a VHF 7100EU, watch mode is similar to a dual watch, scanning between the priority channel and the working channel. However, if you have a VHF 7100US and are operating on USA or Canadian channel banks, you can set the priority channel to cover both CH16 and CH09 as well as the working channel, as follows: RADIO SETUP BEEP VOLUME INT SPEAKER >WATCH MODE WATCH MODE >ONLY 16CH 16CH+9CH 1. Select ONLY 16CH for dual watch mode, or 16CH+9CH for tri watch mode. VHF 7000, 7100US, 7100EU Operation Manual NAVMAN 19 3-6 Weather Alert (Wx ALERT) VHF 7100US only. The NOAA provides several weather forecast channels on USA and Canadian channel banks. If severe weather such as storms or hurricanes are forecast, the NOAA broadcasts a weather alert on 1050 Hz. You can set up the radio to pick up weather alerts, as follows: RADIO SETUP INT SPEAKER WATCH MODE >WX ALERT WX ALERT ON >OFF 1. Select ON (on) or OFF (off) then press ENT to enable the setting and return to the menu. When a weather alert is broadcast, the alarm will sound. Press any key to hear the weather alert voice message. 3-7 NMEA protocol (COM PORT) The radio can be added to a group of instruments using NMEA protocol. RADIO SETUP WATCH MODE WX ALERT >COM PORT NMEA CHECKSUM >ON OFF 1. Select CHECKSUM ON (on) or OFF (off) then press ENT to enable the setting and return to the menu. CHECKSUM ON is the usual setting. 20 NAVMAN VHF 7000, 7100US, 7100EU Operation Manual Section 4 - DSC Setup Menu (DSC SETUP) These DSC facilities are available only on the 7100US and 7100EU and a valid user MMSID must be entered to access the DSC functions. 4-1 DSC Setup - Menu Options The following options are available: USER MMSID GROUP SETUP INDIV REPLY ATIS MMSID ATIS FUNC DSC FUNC LL REPLY Enter your user MMSID. (If you do not have a user MMSID, see Appendix D. ) Enter or change the name and/or details of a group. See section 4. 7. Sections 1. 3 and 1. 4 explain how to navigate around the menu and enter, save and change data. 4-2 Enter Your USER MMSID (USER MMSID) This is a once-only operation. You must enter your user MMSID before you can access the DSC functions. DSC SETUP >USER MMSID GROUP SETUP INDIV REPLY INPUT USER MMSID ­­­­­­­­­ 187654321 MMSID >STORE CANCEL USER MMSID INPUT AGAIN ­­­­­­­­­ You can display and read your user MMSID at any time, but you get only one opportunity to enter your user MMSID. If this is the first time that you are entering your user MMSID, a dashed line appears. Enter your user MMSID along the dashed line. [. . . ] Ph: +86 20 3869 8839 Fax: +86 20 3869 8780 e-mail: sales@peaceful-marine. com web: www. peaceful-marine. com India Access India Overseas Pvt. Ph: +91 120 244 2697 TeleFax: +91 120 253 7881 Mobile: +91 98115 04557 e-mail: vkapil@del3. vsnl. net. in Esmario Export Enterprises Block No. Ph: +91 40 2784 5163 Fax: +91 40 2784 0595 e-mail: gjfeee@hd1. vsnl. net. in web: www. esmario. com Indonesia Polytech Nusantara, Graha Paramita 2nd Floor, Jln Denpasar Raya Blok D2 Kav 8 Kuningan, Jakarta 12940. Ph: +62 21 252 3249 Fax: +62 21 252 3250 e-mail: polytech@transavia. co. id Korea Kumhomarine Technology Co. [. . . ]